How to Hide Wiring: Speaker and Low-Voltage Wire

Updated: May 09, 2023

Ways to hide speaker, telephone, thermostat and other types of low-voltage wiring

FH04MAR_LOWVOL_02-2Family Handyman
Install a home theater and hide the speaker wires with no muss, simple solutions. We'll show you four different ways to take care of it.

You might also like: TBD

A full day


Speakers placed around a room sound great, but all that wire can be an eyesore, an annoyance when you vacuum, even a tripping hazard. You may be able to keep low-voltage wires out of sight and out of your path simply by running them under rugs and behind furniture. If not, here are some solutions for hiding speaker wire—or just about any other type of low-voltage wiring (for phones, thermostats, doorbells, low-voltage lighting, etc.).

Install plastic raceways

Install plastic raceways for speaker wire cover

Plastic raceways are a low-impact way to run wires along trim.

Raceway parts

You’ll need these parts to install plastic raceways.

Raceways come in a range of sizes and shapes, are paintable and often have an adhesive backing for quick installation. You’ll hardly notice a narrow version like the one shown here if it runs along the top of baseboard. Raceways are a lot more noticeable when they run up walls or around doorways, though. Whether you paint your raceway to match the wall or the trim, avoid fussy brushwork by painting before you install it. Touching up any nicks and scratches after installation is easy.

A variety of raceway systems like the Cordmate brand shown are available at home centers and hardware stores.

Video: DIY Hiding Place From Old Books

How to Hide Cable Wires Along Wall or Speaker Wires: Run wire inside walls

Fish wire in walls

Use remodeling boxes, which are easier to mount than nail-on boxes.

Getting wire inside walls takes more time than other methods, but it lets you run wire anywhere invisibly, even past doorways. And it doesn’t have to be a huge project. If there’s an unfinished basement below the room, you can run wires through the basement and into walls. First cut holes in the wall to accept junction boxes. Center the holes 8 to 10 in. from the floor, and you’ll be able to drill down into the basement with a spade bit and extension. Then push a stiff wire (such as wire from a coat hanger) up from the basement and use it to pull the speaker wire down into the basement. You can also run wire through the attic and feed it down into walls, but that cramped, insulation-filled space makes the job a lot more difficult. Any wire used inside walls must be UL-listed.

Stick super-slim wire to walls

Conceal wire

Spread joint compound over wire, sand and paint to blend in with the wall.

Exposed speaker jacks

You can either leave speaker jacks dangling from the wall or for a neater look, install a remodeling box.

Flat, adhesive-backed wire comes in versions for just about any low-voltage purpose. The speaker wire shown here is thinner than a credit card. You can paint it, wallpaper over it or even skim a layer of joint compound over it to make it completely invisible. There’s one situation where this wire becomes noticeable: If you need to turn a corner (to run wire up and over a doorway, for example), you have to fold the wire back over itself. That folded corner creates a slight lump. At the speaker end, simply leave speaker jacks hanging off the wall. Or for a neater look, install junction boxes. Then run the wire right into them and connect the wire to a faceplate with built-in speaker jacks.

Tuck wire between carpet and baseboard

Easy wire hiding

Use a stir stick is a great tool for tucking the wire between the carpet and baseboard.

In rooms with wall-to-wall carpet, you can often force wire between the carpet and the baseboard. This is the fastest, easiest way to hide wire. It’s also the least certain, and the only way to know if it will work is to give it a try. There may be enough space for heavy-duty cable, or you may find it tough to push in even the smallest wire. If there’s a doorway between the power source and the speaker, run the wire all the way around the other side of the room to avoid it. A ruler or paint stir stick makes a good wire-pushing tool. Don’t use anything sharp that might cut into the wire’s insulation.

Video: Dealing With Electrical Wires That Are Too Short

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

  • 4-in-1 screwdriver
  • Cordless drill
  • Drill bit set
  • Drywall sander
  • Electrical tape
  • Paintbrush
  • Safety glasses
  • Tape measure
  • Utility knife
  • Wire stripper/cutter
You might need a fish tape if you’re fishing wires through walls.