9 Tool Hacks You’ll Use Time and Time Again

Tools are usually designed with one task in mind, but many can be used for all sorts of jobs.

1 / 9
Tool bag draped over a ladder for easy access | Construction Pro Tips

Think Outside the (Tool) Box

Tools are usually designed and built with one job in mind, but with a little imagination and some minor adjustments most tools can be used for all sorts of jobs. Take the classic tool belt. Typically, these are made to go around your waist (just like any other belt). But a little bit of creative thinking can turn a tool belt into a makeshift ladder bag. Here are some other great examples of unconventional uses for conventional tools.

2 / 9
Hanging cords on the curved handle of a hook | Construction Pro Tips

Hang Your Roofing Tools

Use spring clamps to keep your hoses, extension cords, and other tools and materials from sliding off the roof. Don’t try this on brittle or scorching hot shingles or you may damage them. You can create a handier hook by sticking the clamp in a vise and bending up one of the handles.

3 / 9
Clamping woodworking projects with a strap | Construction Pro Tips

Clamp With a Tie-Down Strap

If you need to clamp boxes together, a ratchet tie-down strap can often do the job just as well as band clamps. Just make sure to protect the wood under the ratchet and hooks with cardboard.

4 / 9
Mixing concrete in a tub with a rake | Construction Pro Tips

Mix Concrete With a Rake

Try a garden rake instead of a hoe the next time you have to mix concrete. The rake won’t splash as much water over the edge, and the tines do a good job of combining the water with the powder. With a hoe, you waste a lot of time just pushing powder around the tub. A medium mixing tub like the one shown costs around $10 online.

5 / 9
Cutting paint rollers to make mini rollers

Make mini roller covers

Next time you’re in the paint department, pick up a 3-inch roller frame, the type that takes the same diameter cover as a standard 9-inch paint roller. You can then cut any 9-inch roller cover into three 3-inch covers to fit it. A 3-inch roller is perfect for painting trim or small stuff like a mailbox, but not every store carries 3-inch covers. This little trick will also cut the cost of the 3-inch roller covers in half.

Mark the 9-inch roller covers 3 inches in from each end. Cut into equal pieces with a hacksaw, holding the cover steady with a bar clamp. Trim the rough edges of the nap with scissors.

6 / 9
Using a level as a table saw fence | Construction Pro Tips

Use a Level To Extend Your Table Saw Fence

The only way to achieve a perfectly straight cut is to keep your material tight up against the table saw fence. But that’s hard to do when you’re cutting a large sheet of plywood on your own. Extending the fence with a 4-foot level will make it easier to keep the plywood on a straight and narrow path as it approaches and passes through the blade. Hold the level in place with a couple clamps.

7 / 9
Drilling into frozen ground so posts can be planted | Construction Pro Tips

Need a Hole in Hard Soil? Use a Drill!

Have you ever waited too long to install your reflective driveway markers and discovered the ground was frozen? Or tried to install a yard sale sign in dry soil that’s as hard as concrete? Well, why not treat it as if it really were concrete and drill holes into it with a masonry bit? A 3/8-inch x 12-inch bit costs less than $13 at home centers.

8 / 9
Grind off the teeth of a blade so it can cut foam | Construction Pro Tips

Make a Blade for Cutting Foam

A jigsaw will cut through rigid foam like butter—except butter doesn’t crumble into thousands of bits that mess up your shop, basement or garage. If you remove the teeth from a jigsaw blade, it will cut the foam just as well but without the mess. Remove the teeth with a grinder, and be sure to wear eye protection. Hold on to the blade with locking pliers, not your fingers!

Cutting through fame with a de-toothed blade | Construction Pro Tips

9 / 9
Lift heavy things with a pry bar and a piece of wood | Construction Pro Tips

Lift Heavy Stuff With a Flat Pry Bar

If you have ever had to remove a solid-core door, you know how heavy they can be. Lifting them up to reinstall hinge pins can be a challenge if you’re working alone, but a flat pry bar (aka “flat bar”) can give you just the leverage you need.

If your flat bar won’t raise the door high enough, install a small block of wood at the fulcrum point of the pry bar to increase the lifting distance. Hold the block in place with a small screw and washer. Make sure the screw doesn’t poke through. If it does, grind off the end so it won’t damage the floor. This same setup can be used to raise bottom drywall sheets off the floor for fastening.

Harrison Kral
After spending his college summers pouring concrete and building decks, Harrison Kral decided to find a way to put his insider knowledge of construction to use…. just in an air-conditioned setting. He’s an established writer and editor in the DIY space who has written extensively on the home building industry, the housing market, and general DIY trends.