Heavy-Duty Utility Shelves
Refer to the dimensions shown to mark the location of the horizontal 2x2 on the back of four 2x4s. Also mark the position of the 2x4 uprights on the 2x2s. Then simply line up the marks and screw the 2x2s to the 2x4s with pairs of 2-1/2-in. wood screws. Be sure to keep the 2x2s and 2x4s at right angles. Rip a 4 x 8-ft. sheet of 1/2-in. MDF, plywood or OSB into 16-in.-wide strips and screw it to the 2x2s to connect the two frames and form the shelving unit.
If you choose plastic bins rather than cardboard boxes, label the plastic with a wet-erase marker. When it's time to relabel the bin, just wipe away the marks with a damp rag. No room for floor-standing shelves? Build this sliding storage system on the ceiling.
Stud Space Cabinet
When you find a good space, mark the perimeter of the opening and use a drywall keyhole saw to cut it out. Measure the opening and subtract 1/4 in. from the height and width to determine the outer dimensions of your cabinet.
For standard 2x4 stud walls with 1/2-in.-thick drywall, build the cabinet frame from 1x4s that measure 3-1/2 in. wide (see illustration). If your walls are different, adjust the depth of the frame accordingly. Then add a 1/4-in. back.We screwed 1/4-in. pegboard to the back so we could hang stuff from pegboard hooks. Add casing that matches the trim in your house. Drill holes into the sides to accept shelf supports. Shelf supports fit in 3mm, 5mm or 1/4-in. holes depending on the style. Install the cabinet by slipping it into the opening, leveling it and nailing through the trim into the studs on each side. Use 6d finish nails placed every 12-in. along both sides. Don't want to open your walls? Check out these other easy shelving ideas.
The space behind a door is a storage spot that's often overlooked. Build a set of shallow shelves and mount it to the wall. The materials cost about $40.
Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1x2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1x2 trim piece to the sides and top. The 1x2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Locate the studs. Drill clearance holes and screw the shelves to the studs with 2-1/2-in. wood screws. Put a rubber bumper on the frame to protect the door. Don't have an electronic stud finder handy? Learn how to locate studs without a stud finder here.
Joist Space Storage
Closet Nook Shelves
Shoe Storage Booster Stool
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don't have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Stacked Recycling Tower
Five plastic containers, six 2x2s and screws, and one hour's work are all it takes to put together this space-saving recycling storage rack. Our frame fits containers that have a top that measures 14-1/2 in. x 10 in. and are 15 in. tall. Our containers were made by Rubbermaid.
If you use different-size containers, adjust the distance between the uprights so the 2x2s will catch the lip of the container. Then adjust the spacing of the horizontal rungs for a snug fit when the container is angled as shown.
Start by cutting the 2x2s to length according to the illustration. Then mark the position of the rungs on the uprights. Drill two 5/32-in. holes through the uprights at each crosspiece position. Drill from the outside to the inside and angle the holes inward slightly to prevent the screws from breaking out the side of the rungs.
Drive 2-1/2-in. screws through the uprights into the rungs. Assemble the front and back frames. Then connect them with the side crosspieces. Want even more space in the garage? Check out these DIY garage storage tips.
Sandwich Bag Parts Organizer
Two-Story Closet Shelves
There's a lot of space above the shelf in most closets. Even though it's a little hard to reach, it's a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can't hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
The back of a door that opens into a utility room or closet makes a handy hanging space. The trouble is that most doors don't offer a good mounting surface for hardware. The solution is to screw a piece of 3/4-in. plywood to the back of the door. Add construction adhesive for hollow-core doors. Cut the plywood 3 or 4 in. shy of the door edges to avoid conflicts with the doorknob or hinges. Now you can mount as many hooks, magnets and other storage gizmos as you like. Want more behind the door storage? Check out these inside-cabinet door storage ideas.
Double-Decker Closet Rod
Locate studs on the back wall of the closet with a stud finder. Then attach metal brackets to the studs. Use a level to align the brackets along the top. Space the brackets no more than 32 in. apart. Need even more storage? Check out these easy ways to expand your closet space.
Glass Shower Shelf
Tired of the clutter of shampoo and conditioner bottles along the rim of your tub? This tempered safety glass shelf on a cable shelf bracket is an easy solution. The cable shelf bracket requires only two screws for support. If studs aren't located in the right positions, use toggle bolts to anchor the shelf brackets. The glass hangs on the cables. The cable shelf brackets (No. CSB5B) are available online from expodesigninc.com. Order a tempered glass shelf from a local glass company. We installed a 3/8-in.-thick, 12-in.-deep shelf. Want to add some more flair to your bathroom? Learn how to frame your mirror with glass tile here.