Design the cornice to fit your home
Finished cornice close-up
Cornice cross-section and parts
Design elements within your home should dictate the wood type, molding style and finish that you select. Depending on the design, the top either overlaps the sides, sometimes with a routed edge, or is nailed to the top or inside of the box and doesn’t show from below. The tops are best made from 1x4s, 1x6s or 1x8s. There’s no need to cut the tops to width if you choose the right combination of top style and board size. The example we show is a 1×6 nailed on top of the box, which gives an overall inside depth of 4-3/4 in. For the same look but with a shallower box, you could also nail a 1×4 inside the box flush with the top for a depth of 3-1/2 in. Choose whichever method it takes to clear your curtains.
Other Cornice Design Options
A Cornices design options are almost endless. If you’re having trouble choosing, here’s a tip. Buy short lengths of different types of trim along with some cheap 1x4s and 1x6s. Cut everything to 1-ft. lengths and mock up several different combinations. Just squirt a little wood glue on the pieces and clamp them together for about 10 minutes. Hold the cornice mock-ups over the opening to get a feel for the final look.
Select materials and collect key tools
If you plan to paint your cornices, poplar and aspen are good choices for the box materials. They’re stable and cheap, and the grain won’t show through paint. Pine and basswood moldings are usually the least expensive choices for paintable trim.
If you want stained or natural wood cornices, look for oak, mahogany, cherry, maple and others at home centers. The biggest problem is finding hardwood moldings other than oak. You may have to special-order them or find a specialty millwork supplier online.
The best tool for cutting miters on wide boards (1x6s) is either a 10-in. compound miter saw or a sliding compound saw. Standard compound saws work like typical miter saws, but the motor and blade tip sideways, making them capable of cutting bevels. A sliding compound miter saw cuts compound angles too, but the motor and blade slide on tracks so it can handle wider stock.
Be sure to use a sharp finish-cutting blade in either one. Prices for standard compound miter saws are quite low, or you can rent one.
You can predrill and hand-nail most of the project, but an air-powered brad nailer with 1 and1-1/2-in. brads makes the job much easier. Many are inexpensive and well worth the price. Or you can rent one. (Rent one of the special airless ones and you’ll save the price of renting a compressor.) But for the money, compound miter saws and brad nailers are far too useful and far too fun not to own yourself.
Assemble the basic box
Photo 1: Measure carefully
Measure the outside width and depth of curtains, curtain rods or shades that you want to cover and their distances from the wall. Add 1-in. to determine the inside box dimensions.
Photo 2: Cut the boards
Cut 45-degree bevels on both ends of the front board and on one end of each end board. Then reset the saw to 90-degrees and cut the end boards to length.
Photo 3: Join the boards
Smear wood glue on the miters and tack the joint together with six 1-in. brads, three from each side.
Photo 4: Attach the top
Cut the top board to length to fit flush with the front and sides of the box (depending on the design). Glue and nail the top to the box frame with 1-1/2 in. brads spaced every 6-in.
Every wood cornice begins the same way, with cutting and assembling the three-sided, lidded box (Photos 2 – 4). Then you add the trim of your choice (Photos 5 – 9) and finish the cornice (Photo 11). The cornice is then ready for mounting on the wall by screwing it to a 1×2 that’s screwed to the wall above the opening (Photos 12 – 14).
Begin by measuring the curtain and curtain rod for length, depth and width (Photo 1). Measure with the curtains open so you take into account their thickness when bunched. Add an inch or so to the depth and the width of the curtain rod to make sure the cornices will cover everything.
Miter the ends and front box pieces first. It’s easiest to square up the board, then tilt the miter saw to cut a 45-degree bevel for the first end piece and then square it up to cut the second end (Photo 2). The mitered corners are glued and nailed together with 1-in. brads. Measure the assembly to determine the exact length for the top.
Apply the trim
Photo 5: Fit the trim
Using a short test piece, fit the end piece and mark and cut it to fit. Use the test piece to accurately position the trim while you glue and nail it to the box. Cut the miter on the long front piece of trim, fit it to the first piece, mark its length, then cut and fasten it. Repeat the steps for the other end.
Photo 6: Cut the end pieces
Cut the two crown molding end pieces 1-in. longer than needed with opposite 45-degree angles on one end of each piece (you’re cutting a right and a left corner).
Tip: Build up short fences to support crown moldings while cutting by screwing 1×4 boards to the saw fence through the predrilled holes in the fence (shown above).
Photo 7: Attach the crown molding
Flip the box upside down and prop the crown molding end piece against the box. Use the other end as a test piece to line up the miters. Mark and cut the piece to length. Smear a little glue along the bottom and tack it to the cornices with a couple of 1-in. brads.
Photo 8: Finish installing the crown molding
Test-fit, mark and cut the front piece of crown molding to length. Glue and nail the miters together, then nail the molding to the cornice box. Cut and install the last end piece of crown molding.
Photo 9: Install the bottom trim
Cut, fit, glue and nail the bottom piece of trim to the box using the same techniques you used with the crown molding.
When mitering the trim for the box, always start by first cutting and mounting an end trim piece, then the long front trim and finally the other end. That way, you’ll be able to check fits and get crisp miters at each corner. Fit each miter, then scribe the length of each piece rather than measuring (Photo 5). It’s faster and much more accurate. It’s best to cut pieces just a tad long so you can shave them down until they fit perfectly. If you’ re new to woodworking, it’ s nice to have a helper by your side to hold the miters together while you’re scribing lengths or fastening parts.
The trick to cutting perfect crown molding miters is to rest the molding upside down and against the bed and fence while cutting the 45-degree angles (Photo 6). If you cut wide crown molding, you may have to extend the fence height by screwing a length of 1×4 to the miter saw fence through the holes in the back. Remember that the long point of the miter is always the top edge. That’ll help you remember which way to angle the saw before cutting. To further eliminate the costly mistake of miscutting, an angle, draw a light line while you’re fitting the piece to indicate the proper angle (Photo 6).
Smooth and finish cornices
Photo 10: Smooth out the profiles
Fill nail holes and any miter gaps in joints with wood filler. Sand excess wood filler and file miters as necessary to remove any wood fibers or smooth out inconsistencies in profiles.
Photo 11: Prime the wood
Prime the wood and lightly sand it with 150-grit sandpaper before applying your choice of paint.
Fill nail holes and prime before painting. If your cornices have elaborate details like dentil blocking, you’ll get better results with several light coats of spray paint instead of brushing. Finish highly detailed natural and stained wood with spray lacquer, shellac or polyurethane.
Prepaint the 1×2 cornice ledger to match the wall before you put it up if you think it’ll show after the window covering is in place (Photo 13).
Mount the cornice over the window
Photo 12: Center the cornice
Center the cornice over the opening at the height that best covers the curtain rod and curtain. Then reach underneath and mark the bottom. Take down the cornice and extend the mark with a 4-ft. level.
Photo 13: Install the ledger
Cut a 1×2 to fit between the curtain rod brackets. Screw it through the drywall into the framing with 2-1/2-in. screws spaced about every foot.
Photo 14: Drill pilot holes
Predrill 1/8-in. pilot holes spaced about every foot in the top of the cornice 3/4 in. from the back edge. Angle the holes slightly toward the wall. Hold the cornice tight to the wall and run 2-in. screws into the 1×2.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Air Powered Brad Nail Gun
- Cordless drill override and 1/8-in. bit.
- Miter saw
- Safety glasses
- Screw gun
- Tape measure
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 2-1/2-in. wood screws
- Paint or stain
- Sand paper (fine)
- Wood filler