• Share:
How to Replace a Bathtub Spout

Replacing a broken bathtub spout is a simple, inexpensive project. In this article, we'll show you the most common types of spouts, and how to replace them. Even if you've never tackled a plumbing project before, you can handle replacing the spout. And don't worry. You don't need any special skills or plumbing tools.

By the DIY experts of The Family Handyman Magazine

How to replace a tub spout

Bathtub spouts can go bad in three ways: First, the diverter can wear out so it no longer blocks the water flow and sends water to the shower head. Second, the threads inside the spout can crack or corrode where the spout screws onto the pipe. Water can then trickle along the pipe and drip inside the wall. Finally, the spout's finish can flake off or corrode.

Replacement is the solution to any of these problems. A new spout ($10 to $20) and everything else you might need are available at hardware stores and home centers. But before you buy a new spout, determine what type you need. First look under the spout. If you see a setscrew (Photo A), you have a “slip-on” spout.

The setscrew might be smaller and harder to see than the one shown here; you may need a flashlight to spot it. Replacing a slip-on spout is easy: Just loosen the setscrew (usually with a hex wrench) and pull the spout off the copper pipe that protrudes from the wall. Twist the spout as you pull and be gentle so you don’t loosen any pipe connections inside the wall. Then slide on the new spout and tighten the setscrew.

If the spout doesn't have a setscrew, it's a screw-on spout (Photos B and C). Twist the old spout counterclockwise to remove it. If the pipe that protrudes from the wall is copper with a threaded fitting (Photo B), simply cut off the fitting with a tubing cutter ($10) and install a new slip-on spout (Photo A). If the pipe coming out of the wall is steel (Photo C), you need a new screw-on spout.

Ideally, the new spout will fit perfectly onto the old pipe. But there's a good chance that the pipe protrudes too far or not far enough. There's also a chance that the threads are too corroded for you to screw on a new spout. Either way, you'll have to remove the old pipe (Photo 1) and screw in a new pipe of the correct length (Photo 2). Short sections of threaded pipe (called “nipples”) are usually available in 1-in. increments. They cost less than $2 each, so buy a couple of different lengths and save yourself a trip back to the store.

Spout types

These are the three most common types of spouts.

Tip:

Plumbers tell us that leg-shaving is the leading cause of tub spout trouble. The spout makes a convenient footrest for shaving, but that can damage the diverter or loosen pipe connections.

Back to Top

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

    • Caulk gun
    • 4-in-1 screwdriver
    • Adjustable wrench
    • Internal pipe wrench
    • Tube cutter

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.

    • Spout
    • Nipples
    • Thread tape
    • Silicone caulk

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 2 of 2 comments
Show per page: 20   All

October 07, 9:53 AM [GMT -5]

my shower spout is a twist off model my problem is it turns freely but doesnt come off is there anything else i can try?

April 08, 3:46 PM [GMT -5]

My shower has the old 3-handle system with divertor handle. Had to order the replacement on-line to get satin nickle finish. I've replaced the divertor before but wonder if the one I replaced was the original. Still leaks a little when shower is turned on. How do you make sure you have the correct replacement type and can you convert to a different type? Like to the one shown in your repair with divertor on spout.

+ Add Your Comment
closeX

Add Your Comment

How to Replace a Bathtub Spout

Please add your comment
closeX

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today
closeX

Report Abuse

Subject
Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us

Featured Product

Buy Now