My First Time Pressure Washing a Driveway
With all the tools, nozzles, psi ratings and equipment, pressure-washing can be intimidating. But it was easier than I thought it would be. With advice from an expert and a little experimenting, I was able to make my driveway look like new in an afternoon. So, whether you want to extend its life or add a little curb appeal, here are some tips to get your driveway clean in no time.
Time it Right
Pressure washers use a lot of water. If your water is supplied by a well, it’s best to tackle this job when other water use is light. You don’t want to deplete your well on laundry day or when your have a house full of guests. And if you’re in a drought, you may want to postpone for a few months.
Meet the Expert
Vincent R. Christofora Jr. has been a general contractor for 20 years. He’s experienced in all kinds of projects, including landscaping, plumbing and wastewater collection systems.
Watch the how to power wash a concrete driveway video below for more tips.
Tarp your plants
Concrete detergent can harm plants; before you begin pressure washing, cover them with tarps. I used canvas drop cloths, but they can be expensive. For a cheap, lightweight option, use a roll of painter’s plastic. Remove the tarps as soon as possible to avoid overheating the plants.
Blow away debris
Moving piles of debris with a pressure washer is a waste of time and water. Instead, use a leaf blower to clear away smaller debris like leaves, rocks, sticks and mulch. You can use a broom, but a leaf blower is faster and easier. Don’t rush this step, and clear as much as possible.
Wear safety gear
Pressure washers are loud, the water and other debris can splash back in your face, and you’ll be stepping around slick, soapy water. Always wear safety glasses, hearing protection and close-toe shoes with good traction. A powerful pressure washer can actually cut skin. Use it with caution, and keep it away from children.
Bigger is faster
The greater the pressure washer’s psi rating, the faster the cleaning job. I tested three pressure washers: 1,600, 2,300 and 3,100 psi. There’s no doubt that electric pressure washers from 1,300 to 2,300 psi can wash a concrete driveway, but it’ll take longer. If you have a large driveway with lots of stains, you’ll want more power to do the job faster. I chose the 3,100-psi gas pressure washer and cut the job time in half.
Searching for a power washer? Check out our power washer buying guide.
Purge the hose
Once you’ve connected the garden hose from the spigot to the pressure washer, don’t be too eager to turn on the pressure washer. Instead, squeeze the trigger for roughly 30 seconds until a nice, steady stream comes out. This releases the air from the hose and preps the machine for a strong blast. Learn more pressure washer maintenance tips.
Choose the right nozzle
Nozzles are calibrated in degrees, and the lower the number, the narrower and more powerful the stream. I experimented with various nozzles and settled on three: For dousing the concrete with detergent, a 65-degree worked well. For the actual cleaning, a 25-degree was fastest. For tough areas, I used a 15-degree nozzle. Pick up a 5-in-1 dial nozzle (about $25 at home centers) to make changes quick and easy.
Concrete under the gun
You would never use a 0-degree nozzle to wash concrete, but I couldn’t resist giving it a try. I used a 3,100-psi gas pressure washer and placed a 0-degree nozzle just a few inches from the concrete. In seconds, I carved a zigzag line with ease. After 45 seconds, the pressure washer left a small crater. Pressure washers can deeply damage concrete, but it’ll take some effort. In normal circumstances, all you really need to worry about is light surface etching. Check out the damage it did in the video below.
Experiment on a less visible spot and wash other surfaces first
If you hold the nozzle too close to the driveway, the pressure can etch the concrete surface. The distance depends on the power of your pressure washer and the nozzle you’re using. Try experimenting on an inconspicuous spot and see how close you can get without damaging the concrete.
Plan ahead and work from top to bottom. If your roof, siding and retaining walls need to be washed, do them first. Otherwise, dirty water will run off those surfaces and ruin your clean driveway.
Use a detergent
Concrete detergent is incredibly effective. I tried pressure washing without it, and the result didn’t come close. It helps remove stubborn oil, paint and dirt stains. I used Zep Driveway & Concrete Pressure Wash detergent, but many great options are available. New pressure washers often include a soap tank to apply the detergent. Wave the wand back and forth roughly 8 in. off the surface to create a nice lather. Let it sit for 10 minutes and then wash. Don’t pour bleach or other chemicals into your pressure washer soap tank.
Read the detergent instructions
Concrete detergent is a powerful chemical— if you don’t use it correctly, it could ruin your driveway. Used at full strength, it can leave ugly white spots or streaks.
Before you clean the entire surface, spot-treat the oil stains. I saturated these stains with diluted concrete detergent solution from a spray bottle. Let the soap sit for 10 minutes, then rinse with the pressure washer. Some stains are tough to remove—paint stains clean up quickly, but oil and rust stains take longer. If your stain isn’t disappearing, treat it a few more times with a less diluted solution.
Start at the top
Start at the high end of your driveway and work your way down. You don’t want dirty water running over the places you just cleaned. That might sound obvious, but it’s easy to start at the bottom without thinking about it. Also, be sure to park the pressure washer near the high spot so you’re dragging the hose behind you, rather than constantly kicking it out of your way. These are 13 things you should never power wash.
Work in small sections
If you spray your entire driveway with soap all at once, it’ll settle and dry before you can wash it off, which could leave white stains and streaks. Instead, soap and wash in 10 x 10-ft. sections. On my driveway, I found the joints in the concrete to be a natural guide.
Extend your reach
Pressure washers are no fun to lug around. Do yourself a favor and buy a pressure washer extension hose. They come in 25-ft. and 50-ft. lengths ($45 to $75). I attached a 50-ft. hose to the 25-ft. hose that came with the machine. Be sure the coupler you choose is compatible with your equipment.
Get a surface cleaner
It takes a lot of time and effort to clean a driveway with a nozzle. You can cut both in half by using a pressure washer surface cleaner. And they’re affordable, ranging from $20 to $90. The one I used cost $88 online and was worth every penny. As you use it, pull it from side to side rather than pushing it. Also, hold the wand upright to avoid putting pressure on your back.
Wash edges with a nozzle
The surface cleaner doesn’t clean the edges along retaining walls, posts or other structures, so you have to clean those with a nozzle. Use a 25-degree nozzle for deep cleaning and a 40-degree nozzle for rinsing away standing water.
Protect your driveway with a sealant
After you’ve done the work to clean your driveway, consider sealing it. A good sealer will protect your driveway, help it last longer and make future cleaning much easier. Be sure the driveway is dry before you begin.