Cheap Workshop Storage Solutions You Can DIY
Tame the clutter and work smarter with these ingenious (and inexpensive!) workshop storage tips you can DIY.
Air Tool Station
Sealed and Stored
Here’s a great way to reuse empty CD/DVD containers. Drill a hole in the top for the string to slide through, then screw the lid under a shelf and snap on the string-loaded container. Pull down and snip off the desired length and never worry that your ball of string will roll away across the floor dragging its tail behind it!
C-Clamp Paper Towel Rack
Create an instant paper towel dispenser with two C-clamps. Position and clamp them a roll’s width apart in a convenient spot, hold up the roll and push in the handles to hold it. Buy slick-looking C-clamps and install them in the kitchen, then fib to visitors about your chic designer hardware.
Muffin Tin Hardware Bin
Attach a muffin tin under a shelf with a single 1/4-in. x 1-1/2-in. flat head machine screw. The tin pivots out from beneath work surfaces to organize and serve up any little doodad you frequently use. And you store all that little stuff without using up a single square inch of workspace. For best results when installing your muffin bins:
- Use muffin tins made from heavier gauge metal.
- Drill and countersink a 1/4-in. hole in the shelf top, so the top of the screw is flush with the shelf.
- Place 1/4-in. fender washers above and below the rim of the muffin tin.
- Tighten two nuts against each other on the underside so the threads won’t loosen.
On-a-Roll Pegboard Doors
The trick is to insert 1/2-in. plywood spacers in the roller hardware as shown. You can use the floor bracket that comes with the slider hardware to maintain the same 2-in. clearance at the bottom of the cabinet. For door handles, simply drill a couple of 1-1/4-in. holes in the pegboard with a spade bit. Now pop in the pegs and hang up your tools.
- One 3/8-in. x 24-in. x 7-1/8-in. plywood piece for the sides
- One 3/8-in. x 24-in. x 4-3/4-in. plywood piece for the floor
- Two 1/2-in. x 4-1/2-in. x 4-in. plywood pieces for the ends
- Five 1/8-in. x 4-1/2-in. x 4-3/8-in. hardboard partitions
On a table saw, cut 3/16-in.-deep slots every 4 in. across the 24-in. x 7-1/8-in. piece of plywood. Make the slots just wide enough for the 1/8-in.-thick partition to slide in smoothly. Now saw the slotted piece into strips 4-1/2 in. and 2-1/2 in. wide. Use 1-in. brads and glue (predrilling for the brads) to assemble the sides and angled ends, then nail and glue on the floor. Drop the angled partitions into the slots, mount the rack to a wall, and go nuts sorting and organizing your scattered hardware. Here’s another seriously simple, space-saving storage solution for your workshop.
Here’s an instant rack for hammer storage. Drive 2-in. drywall screws into a board and tack it to a shop wall. Hook the hammers on the screws so it looks like they’re ready to pull out a nail. The hammer claw’s V-notch interlocks tightly with the screw threads so the hammer won’t fall off, and the handle angles toward you for an easy grasp.
Adjustable Drawer Partitions
Apply weatherstripping to the sides of the drawers as shown, then cut the partitions long enough so they squish firmly into the rubber on both ends. A good rule of thumb is to make the partitions 1/4 in. longer than the inside measurement between the weatherstripping.
To install a partition, hold it at an angle to the front and back sides, then rotate it into position.
In this drawer, movable partitions are held in place by strips of foam weather stripping at the front and back. The 44-plus boxes rest on edge, labels up, for easy grabbing and stowing. The labels are typed on a computer and printed on sticky label sheets. Think of never having to wonder where to find a 1-in. drywall screw or a 3/8-in. washer!
Shop for boxes at craft, tackle, office or dollar stores or online.
Saw Blade Roost
Using a handsaw, cut notches spaced at 3/8-in. intervals halfway through a 5/8-in. dowel. Glue the dowel in a hole drilled in a 16 x 12-in. piece of 3/4-in. plywood. Frame the sides and lower edge of the plywood with 2-in. strips of plywood and add a lower facing piece to create a basin at the bottom.
When a blade needs cleaning, remove the other blades and line the rack with tinfoil. Then mount the gunked-up blade on the dowel, spray one side with oven cleaner, and flip it over and spray the other side. Any drips go in the basin, and the sides minimize overspray. Let the cleaner work for an hour or so, then use a moistened kitchen scrub pad to scour the dissolved gunk and burned sawdust off the blade. Then throw away the foil and store your blades. Check out this genius blade storage idea from one of our readers.
Storage Pockets for Skinny Things
Tape and Glasses Hanger
A 1/8-in.-thick strip of steel or aluminum fastened to a wall with 3/4-in.-thick spacers makes a great holder for tape measures, safety glasses and other stuff that doesn’t hang easily on hooks.
Table Saw Basket
Here’s a solution for keeping all your table saw paraphernalia— push sticks, miter fence, extra blades, wrenches—in easy reach and free of sawdust. Attach a plastic storage basket under one side of the saw table with four pieces of stout, vinyl-coated wire. Table saw designs vary, but most have predrilled holes in the wing edges, and you may be able to temporarily loosen a couple of bolts under the table, like we did, to twist the wire on and retighten the bolts to hold it. For best storage, add a plywood shelf or two, drilled out with a large spade bit so it won’t collect dust. Attach the shelves with 3/4-in. machine screws through the plastic into the plywood.
Tabletop Chisel Storage
Start with a 4-in.-wide board. Using your table saw, cut stopped slots to match the width and depth of each chisel (plus some wiggle room). Screw or glue on another board to create the pockets, then run the lower edge of the doubled board through a table saw with the blade set at 15 degrees. Now cut three triangular legs with 75-degree bottom corners and glue them to the pocket board. If you like, drill a few holes through the boards for pegboard hooks so the holder is easy to store on the wall.
Flip-Through Storage Rack
Mount two parallel 2x4s on the wall spaced 24 in. apart. Cut the leaves from 3/4-in. plywood and hang them from the 2x4s with 3-in. door hinges. Fur out the hinges with 3/4-in. plywood blocks so the pages can pivot without binding. Mount the leaves at least 4 in. apart to allow room for them to fold back. Let your imagination run wild creating holders for your various tools.
For you pegboard fans, sandwich a 1×3 frame between two pieces of pegboard. Now your collection of hooks and holders will work with this tool storage system. Check out these other simple storage solutions for small spaces.
PVC Pipe Clamp Rack
To make the rack, cut 2-in. lengths of PVC, and with a hacksaw or band saw, slice them lengthwise about 3/16 in. past the diameter’s center line. This creates the gripping action to firmly hold the heavy iron pipe. Drill and countersink two holes in each PVC piece, then space and screw them along a pair of 2-in.-wide boards. Attach the upper board to your shop wall and snap a pipe clamp in either end to position the lower board for screwing to the wall. Plus: 28 secret clamping tricks from woodworkers.