Save on Pinterest

Stackable Shelves

It's shelving, storage, a desk and work surface combined

FH01OCT_STACKS_01-2Family Handyman

Make your own stackable shelves. A simple shop-made jig makes this project simple to build and a snap to assemble.

You might also like: TBD

Time
Multi-day
Complexity
Moderate
Cost
$100 – $500

Construction details

Photo 1: Rip the pieces

Rip your 1/2-in. plywood into pieces to make the standards, then cut the lengths with a circular saw. Cutting large sheets with a straightedge guide and a circular saw is easier than wrestling large sheets through a table saw.

If you need shelving, storage, a desk or a work surface, check out this modular system. It’s got lots of storage space for your electronic gear and books and a nifty recess to accommodate a stool. And you can easily customize this system to suit your storage needs and wall space.

The T-shaped standards (Photo 5) are simple to cut and glue. (We used Baltic birch because we liked the look of the multiple laminations on the edges, but any 1/2-in. hardwood plywood will do.) We chose sturdy, easy-to-clean 3/4-in. Melamine for the horizontal shelves because it has a tough, plastic-like surface, but you can use plywood, MDF (medium-density fiberboard) or particleboard and paint it any color you wish.

The plywood standards and the shelves are drilled precisely with a homemade jig (Photos 4 and 6 and Fig. B) and are held together with 3/8-in. dia. steel pins. The pins slide through the shelves and into the standards, so putting this together is sort of like stacking blocks or Lego pieces.

Figure A: Stackable Shelves Detail

The layers of stackable shelving are held together with steel pins. For a complete Cutting List and a PDF of Figure A, see “Additional Information” below

Glue the front pieces together for each standard and then “sandwich clamp” them

Photo 2: Glue the part A’s together

Glue together the two pieces that make up part A of the standards. Nail the two pieces together at two corners with 3/4-in. brads once you’ve aligned them. This keeps them from drifting apart when you clamp them.

Photo 3: Clamp the pieces

Clamp three laminated pairs (A) together using 2x4s to help distribute the pressure evenly across the sheet surface. Leave the assembly clamped for at least two hours.

Photo 4: Build the T-shaped standards

Glue and screw the 1/2-in. plywood back (B) to the laminated part A to form the T-shape of the standard. Be sure to center the standard and make sure everything is aligned. The jig will help with the correct alignment.

Photo 5: Add parts C

Glue and clamp parts C to each standard. Be sure to glue around the perimeter of each piece and also run a bead of glue along the inside corner. Use as many clamps as necessary. For tall standards you may need up to four clamps per side. Remove the standard from the jig and glue another standard together while the glue sets.

Photo 6: Drill holes for the steel pins

Drill 25/64-in. dia. holes 1 in. deep into the tops and bottoms of the standards at the locations shown in Fig. B. We used a portable drilling guide (available at home centers) for precise perpendicular holes. You can also use a drill press, if you have one. If you have a good eye for drilling straight holes, you can drill freehand.

Photo 7: Cut the pins

Cut the assembly pins from 3/8-in. rod using a hacksaw or jigsaw. File the burrs on the cut edge to make the pins easier to slip into the holes.

Photo 8: Drill pin holes

Drill the pin holes in the shelves using the same 25/64-in. drill bit and an accessory fence screwed to the jig. The auxiliary fence positions the jig automatically to ensure consistent overhang from the standards. Be sure to set the depth stop on your drill so you don’t drill through the top piece of your shelving unit, which is located on the bottom of the stack as shown.

We went to all the trouble of gluing the 1/2-in. plywood standard fronts together to create a more stable, 1-in. thick support. This thickness also allows us to use 3/8-in. pins in the assembly for more strength and sturdiness. It would take you a month of Sundays and dozens of clamps to individually clamp all the standard fronts together. Instead, get all your pieces cut and ready to glue and then clamp three or four pairs together at one time as shown in Photo 3.

Figure B: Drilling Jig Detail

Build a jig to assemble and drill the T-shaped shelf standards

You can’t successfully build this project without maintaining exact consistency. This handy jig will help. You make the jig by gluing and nailing 1/2-in. plywood strips to a 3/4-in. scrap plywood base. Use a square to lay out everything precisely as shown in Fig. B. This jig helps you assemble the parts of each standard precisely. And you can flip it over and use it to accurately drill the pin holes (Photo 6).

The jig will also be your guide for drilling the holes into the horizontal shelf boards, which need to perfectly align with the standards (Photo 8). All you need to do is screw an auxiliary fence to the jig to maintain the proper overhang on the front and back of each shelf. (For a larger, printable PDF of Figure B, see “Additional Information” below.)

Measure the height and width you need for each shelf

Photo 9: Add the shelf edging

Iron the preglued strips onto the edges of the shelves. Use a medium to high setting on the iron. When the glue has set, use a special edge trimmer (available at home centers) for perfect edges. After trimming the edges, sand the edges lightly with 220-grit sandpaper or a fine mill file.

Photo 10: Use a carbide-tooth blade

Cut your Melamine or plywood using a 60-tooth carbide blade in your circular saw. Cut with the good side down to minimize chipping. If you’re using black Melamine,you can hide minor chipping with a permanent marker.

Photo 11: Stack the shelves and standards

Assemble the standards and shelves one tier at a time. Begin by positioning the bottom standards, then continue adding shelves and standards.

Tap in the pins

Align the shelf and tap the pins through the shelf and into the standard.

If you plan to alter this project to suit your personal stuff, establish the height of each shelf so you can cut the plywood for the T-shaped standards. Measure the heights of things you plan to display, like a TV, stereo equipment, computer or books. Also, leave some room from the top shelf to the ceiling.

You don’t want your new shelves to sag, so don’t exceed a span of 29 in. between the rear wings of the standards. The span is measured from the closest points between the T-shaped standards (Photo 11). For example, if the front edges of your standards are 38 in. apart, the rear wings of the T-shaped standards will be close to 27 in. apart—well within the limit.

Choosing Materials

Melamine is tough to cut without chipping. If this is one of your first projects, you may want to consider using a different shelf material. In some areas, the black will be difficult to find unless you have a full-service lumberyard special order it. White Melamine, however, is sold in 3/4-in. thicknesses in most home centers.

Hardwood plywood with iron-on wood edging or MDF (medium-density fiberboard) are excellent substitutes for 3/4-in. Melamine. You can sand the edges of MDF easily, and it paints beautifully because it’s so smooth. Plywood is readily available as well, but you’ll need either 1/4-in. glue-on strips or iron-on wood edging to cover the exposed edges. You can then stain, varnish or paint the plywood.

Baltic birch may also be tough to find in some areas. It’s usually sold in 5-ft. square sheets. We used nine-ply sheets because the cut edges look great when sanded and finished. Each layer, or ply, stands out. And unlike with other plywood choices, there are no voids. You can buy Baltic birch with one good side and the other made from lower-quality veneer. This makes the most sense for this project because you can hide the bad side. Other types of plywood with no voids are available. You can also substitute any hardwood plywood, but you may need to glue hardwood strips over the edges to hide voids.

Additional Information

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

  • Circular saw
  • Clamps
  • Cordless drill
  • Drill bit set
  • File
  • Forstner drill bits
  • Framing square
  • Hacksaw
  • Jigsaw
  • Miter saw
  • Orbital sander
  • Rubber mallet
  • Safety glasses
  • Straightedge
You also need a clothes iron, a portable drilling guide or drill press, and a laminate trimmer.

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • 3/4-in. brad nails
  • 3/8-in. steel rod
  • Baltic birch
  • MDF
  • Wood edging
  • Wood glue

Additional Information