Save on Pinterest

How to Make a Squirrel Feeder

Have fun with this “squirrel-under-glass” feeder

entertaining-squirrel-feeder-outside
This feeder provides an unusually clear view of the squirrels that frequent it, because the bold critters actually climb inside the feed jar to eat!

You might also like: TBD

Entertaining Squirrel Feeder

This entertaining squirrel feeder requires only a minimum of materials. All that’s needed is a 6-ft. fence board, a handful of screws and a 1-gallon glass jar. If you don’t have the glass jar, or don’t want to eat a year’s supply of pickles to build this feeder, ask local restaurants, schools or other establishments that buy food in bulk if they have a jar to spare. Just be sure it has an inside diameter of at least 6 in., so the squirrels can dine in comfort. Plus, check out these 16 seriously cool birdhouses.

How to Make a Squirrel Feeder Project Directions:

entertaining squirrel feeder inside

  1.  Cut the pieces from a 6-ft. 1-in. x 6-in. fence board according to the board layout at left.
  2. Make the jar support (F) by tracing the curve of the jar onto the wood. The lowest point of the curve should be 1 in. from the bottom of the board. Cut along the line with a saber saw. Place the jar on the support to check that it fits well. Trim the sharp corners off the support (about 1/4 to 1/2 in.) and smooth rough edges with sandpaper. The curved piece (G) remaining from this will become the end piece.
  3. Cut entrance holes in both side pieces. Mark a spot about 3-1/2 in. from the highest corner of each board and center the hole from side to side. Draw a 3-in.- diameter circle with a compass, then cut out the holes with a saber saw. Smooth rough edges with sandpaper.
  4. Make a hole in the front of the feeder to hold the neck of the jar. This is a tricky step because jars vary in size. Start by determining the radius of the jar’s mouth. Then lay the jar on its side and measure from the tabletop to the bottom of the mouth. Add these two measurements plus 1 inch. Mark this distance from the bottom of the front board and center. From this point, draw a circle 1/2 in. larger than the diameter of the mouth. Cut the hole with a saber saw.
  5. Assemble the front and sides of the squirrel feeder, then attach the assembled pieces to the base. These joints, and all others, will be fastened with 1-5/8-in. galvanized deck screws. Cedar splits easily, so be sure to drill pilot holes in each piece before driving in the screws.
  6. Attach the jar support about 3 in. from the far end of the base. Then position the rounded end piece—which keeps the jar from sliding out of the feeder—at the edge of the base. However, make sure there is enough clearance for you to tip the jar out for filling. If it’s too tight, use a rasp to round the inside curved edge of this end piece until the jar can easily be removed. If the jar is too loose, move the rounded end farther up the base before attaching it.
  7.  Predrill holes in the top and bottom of the mounting board. Then attach the mounting board to the feeder with 1-5/8-in. deck screws.
  8. If you’d like to make a beveled edge on the roof piece so it tightly meets the mounting board, cut a 15-degree angle on the back edge of the roof with a table saw. Then attach it to the feeder.
  9. Mount the feeder on a tree with 2-1/2-in. deck screws (this is a heavy feeder—you’ll need large screws to mount it securely) and fill it with peanuts in the shell, cracked corn or birdseed. Then check your watch. It won’t be long before you’ll be inviting the neighbors over to admire your “squirrel under glass!”

entertaining squirrel feeder half way

How to Make a Squirrel Feeder Project PDF’s:

Click the links below to download the construction drawings, materials list as well as the cutting list for this project.

Figure Afigure a entertaining squirrel feeder

Shopping list:

  • 1 1″x6″ x 6′ “dog-eared” cedar fence board
  • 2-1/2′ and 1-5/8′ galv. deck screws
  • 1 1-gallon glass jar

Recommended tools: 

  • Saber saw
  • Compass
  • Rasp or rough sandpaper