Saturday Morning Workshop: How To Build An Adjustable Sawhorse

Add these ingenious, handy, adjustable sawhorses to your jobsite arsenal.

Next Project
Time

A few hours

Complexity

Intermediate

Cost

$51–100

Introduction

Every workshop needs a couple of sawhorses, and this design is especially useful. This adjustable version of a classic creates the ultimate sawhorse. The special adjustable support can be raised as much as 20 in. to give you either a more comfortable working height or a great out feed table. Follow the video tutorial and step-by-step plans below, and you can build a set of these adjustable sawhorses in just a few hours!

Tools Required

  • Chisel
  • Drill/driver
  • Hammer/Mallet
  • Miter saw
  • Punch
  • Speed square
  • Table saw

Materials Required

  • 1-1/4 in. construction screws
  • 1/2-in. plywood
  • 1x4 board
  • 2-1/2 in. construction screws
  • 2X2 board
  • 2x4 board
  • 3/8-in. x 5-in. carriage bolt

What It Takes

  • Time: 3 hours
  • Cost: $60 each
  • Skill level: Intermediate

Cutting List

Adjustable Sawhorse

Tech Art

Adjustable Sawhorse Tech Art

After you build your adjustable sawhorse, try another Saturday Morning Workshop project that will help you create the perfect work space!

We obviously want you to break out your tools and build this beauty. But if that isn’t in the cards, check out this adjustable sawhorse from Amazon.

Project step-by-step (10)

Step 1

Crosscut boards to length

Adjustable Sawhorse Crosscut boards to length

Crosscut the following boards to length on the miter saw:

  • 2x4 board to one 42-in. piece for the adjustable support top (A)
  • 2x4 board to two 27-in. pieces for the adjustable support uprights (B)
  • 2x4 board to one 36-in. piece for the spacers
  • 2x4 board to one 42-in. pieces for the side rails (E)
  • 2x2 board to two 37-in. pieces for the lower guides (K)
  • 1x4 board to two 37-in. pieces for the front/back braces (G)

Step 2

Rip and bevel pieces for the top assembly

Adjustable Sawhorse Bevel

Rip the rounded edges off of the 2x4 board, the board should be about 3-in. wide. Bevel a 20-degree angle through the center of the board as shown above on the table saw to create the side rails (E). Rip the spacer 2x4 board to 1-5/8 in. on the table saw. Use the miter saw to crosscut the 1-5/8 in. board to two 6 in. lengths for the outer spacers (C) and one 18 in. length for the inner spacer (D).

Step 3

Fasten together the top assembly

Adjustable Sawhorse Top Assembly

Fasten the side rails to the outer spacers (C) with 2-1/2 in. construction screws, leaving 2-1/2 in. reliefs on both ends. Place 2x4 offcuts into the adjustable support gaps and center the inner spacer (D), fasten with 2-1/2 in. constructions screws to create the top assembly.

Step 4

Cut the half lap joint notches

Adjustable Sawhorse Half Lap Joints

Mark a 3-1/2 in. x 3/4-in. notch into the adjustable support uprights (B) and two 3-1/2 in. x 3/4-in. notches into the adjustable support top (A), 8-1/2 in. from the ends. Set your table saw blade to 3/4-in. and run the boards with a miter gauge to create numerous kerfs for the half lap joints. Hammer out the leftover wood. Chisel the notch flat and sand to smooth to create the final half lap joint.

Step 5

Drill holes into the adjustable support uprights

Adjustable Sawhorse Drill holes into the uprights

Mark out 2 in. increments, centered into the faces of the adjustable support uprights (B). Use a speed square to make sure the holes line up across both uprights. Mark the hole locations with a punch and hammer. Drill the holes with a 1/2-in. spade bit into a sacrificial board to reduce blowout.

Step 6

Fasten together the adjustable assembly

Adjustable Sawhorse Create adjustable assembly

Fit the adjustable support upright (B) notches into the adjustable support top (A) notches and fasten with five 1-1/4 in. construction screws into each to create the adjustable assembly. Use a speed square to make sure the uprights are at a 90-degree angle.

Step 7

Bevel and attach the legs to the top assembly

Adjustable Sawhorse Create and attach legs to the top assembly

Miter an initial 20-degree angle into one of the 1x4 pine boards with the miter saw, measure 30-5/8 in. and then cut another, parallel miter for the four legs (F). Flip the top assembly over and temporarily fasten the legs to the top assembly with 2-in. 18-gauge brad nails. Fasten the legs permanently with 1-1/4 in. construction screws.

Step 8

Make and fasten the gussets

Adjustable Sawhorse Gussets

Rip the 1/2-in. plywood to a 6 in. strip. Scribe both sides along the legs. Cut the angle on the miter saw to create the gussets (J). Repeat for the other end cap. Fasten the end caps directly to the legs with 1-1/4 in. construction screws.

Step 9

Fasten the guides and leads to the sawhorse

Adjustable Sawhorse Guides

With the adjustable assembly into the rest of the sawhorse, temporarily fasten the 2x2 lower guides (K) to the gussets (H) with an 18-gauge brad nail gun so the the bottom of the 2x2 is flush with the bottom edge of the gussets (H). Make sure the adjustable assembly has a 1/8-in. gap on either side to allow for some play. Permanently fasten the lower guides (K) with 1-1/4 in. construction screws. Rip the 1/2-in. plywood to 4-1/2 in. on the table saw and crosscut 1 in. pieces out of that strip for the guide stays (L). Fasten the guide stays (L) to the top of the support leaders with 1/8-in. gaps between the support assembly and the guide stays (L).

Step 10

Fasten the leg braces

Adjustable Sawhorse Scribe ends

Fasten the 1x4 front/back braces (Part G) 15-1/2 in. from the top of the legs (F) directly to the face with 1-1/4 in. construction screws. Take the end braces to the sawhorse and scribe the angles into the end brace board. Cut the mitered angles on the miter saw to create the end braces (H). Fasten the end braces (H) to the edges of the legs (F) with 1-1/4 in. construction screws. Repeat on the other side to complete the sawhorse.

Family Handyman