How to Restore a Vintage Console Stereo

Vintage style, modern sound!

Our editors and experts handpick every product we feature. We may earn a commission from your purchases.

Next Project
Time

Multiple Days

Complexity

Intermediate

Cost

$600-700

Introduction

This 1960s console stereo had so much potential, we weren’t going to let a little water damage and outdated electronics doom it to a landfill. Using simple woodworking techniques, we refurbished this console and added to its high style. Then we filled it with 21st-century audio goodies.

The best part? We’ll show you how to do the same.

Tools Required

  • Band saw
  • Basic woodworking tools
  • random orbital sander
  • Router
  • Table saw

Materials Required

  • 1-3/4" x 10" x 60" mahogany
  • 3" No. 10 washer-head screws
  • 3/4" No. 8 wood screws
  • 6/4 x 9" x 48" sapele
  • Cold press veneer glue
  • Gel stain - Java
  • Hide glue
  • Oil-based semigloss topcoat
  • QuikWood Epoxy Putty
  • Sapele veneer
  • Speaker cloth 1 yd.
  • White craft glue. Gel stain - Antique Walnut

Restored Vintage Console Stereo finished project in a living roomTMB Studio

There are four phases to this furniture restoration project.

Phase 1: Fix Cosmetic Damage (Steps 1 through 6)

When I found this vintage console stereo, it was in rough shape. The legs had broken through the particleboard bottom. So first I had to attach a new plywood base, fill the chips and nicks, hide water damage and address other cosmetic work.

Phase 2: Rebuild The Front Panel (Steps 7 through 14)

The center panel needed to be covered in place. I chose a four-way bookmatch pattern with sequence-matched leaves of figured sapele veneer.

The speaker cloth was faded, so I replaced it with classic black ($18 per yard, parts-express.com) and designed new slats to lay over the top.

Phase 3: Make New Legs (Steps 15 and 16)

I chose sapele for the new legs because it was a good match for the veneer on the front panel. Sapele looks like mahogany and is similar to work with, but often has a pronounced ribbon figure, which I love. I found pre-milled 6/4 sapele at a local lumberyard.

Phase 4: Final Touches (Steps 17 and 18)

I finished the console and update the audio components for modern functionality and high quality sound. Check out our guide to old furniture restoration.

Project step-by-step (18)

Step 1

Fit a New Bottom Panel

  • To start, attach a new plywood base.
  • I predrilled 16 holes in 1/4-in. Baltic birch plywood and spread the glue evenly with a glue spreader.
  • Then I screwed the plywood to the old bottom with 3/4-in. wood screws.
    • Pro tip: I did this step first because the console had to be upside down, and I needed to repair the top later anyway.

Console Stereo Fh22mar 616 51 025Family Handyman

Step 2

Inspect Water Stains

  • This water stain could have been worse. It only damaged the finish.
  • The underlying particleboard wasn’t swollen and the wood veneer only slightly discolored from UV light.

Console Stereo Fh22mar 616 51 004Family Handyman

Step 3

Rub Shellac into the Damaged Area

  • A little shellac restores the natural tone in the damaged wood where the finish is gone.
  • With a piece of 600-grit wet/dry sandpaper, work a small amount of shellac into the damaged area.
  • Wipe off excess with a clean cloth dampened with denatured alcohol. This rejuvenates the natural tone of the damaged wood and fills in the grain.

Console Stereo Fh22mar 616 51 026Family Handyman

Step 4

Add Stain to Even Out the Color

  • I let the shellac dry for an hour, then artistically applied the first layer of stain to blend out any evidence of damage.
    • Pro tip: Let this stain dry for at least a day.

Console Stereo Fh22mar 616 51 037Family Handyman

Step 5

Fill Chips and Nicks with Wood Putty

Console Stereo Fh22mar 616 51 030Family Handyman

Step 6

Stain and Topcoat the Entire Console

  • After repairing damage with wood putty, I applied the first coat of stain to the water spots.
  • When it dried, I applied a final coat of stain to darken the entire vintage stereo console by about one shade.

Console Stereo Fh22mar 616 51 079Family Handyman

Step 7

Prepare the Veneer

  • I determined the size of each quadrant and cut two blocks of 3/4-in. plywood two inches longer and two inches wider.
  • Stack four leaves of veneer and use the plywood as a guide to cut all four at once with a utility knife.
  • Figured veneer needs to be flattened before glue-up, so I sprayed the leaves with Veneer Tamer from Woodcraft and laid pieces of craft paper between the leaves.
  • Stack everything between the two pieces of plywood and place heavy weights on top.
  • Replace the paper once a day to help draw out all the moisture. Do this until the veneer is completely dry.

Console Stereo Fh22mar 616 51 050Family Handyman

Step 8

Cut the Veneer to Size

  • Drill small pilot holes along two edges and drive short screws through the stack.
    • Pro tip: Make sure the screws don’t go through the other side!
  • Cut the block to width on a table saw, then cut it to length on a miter saw.

Console Stereo Fh22mar 616 51 021Family Handyman

Step 9

Veneer the Panel

  • Spread a thin layer of veneer glue on the back of each veneer leaf and lay it face down (Photo 3A).
  • The veneer may curl slightly as the glue dries. Don’t worry, it’ll lie back down. Spread a layer of glue on the substrate and allow everything to dry overnight.
  • Once the glue dries, spread one more thin coat of glue on all surfaces and allow that to dry for about an hour.
  • Perfectly center one leaf on the substrate. With a household iron set to cotton, run the iron slowly and firmly over the entire leaf (Photo 3B). This briefly reactivates the glue, joining the veneer to the substrate.
  • Once the first leaf is complete, repeat this process for the remaining three.

Console Stereo Fh22mar 616 51 053Family HandymanConsole Stereo Fh22mar 616 51 069Family Handyman

Step 10

Make New Baffles

  • I used 1/4-in. Baltic birch to make the speaker baffles.
  • To accommodate the new speakers, I cut a rectangular hole with rounded corners 1-1/2-in. from the bottom and one inch from the sides.
  • Check for fit and paint the baffles black with water-based paint.

Console Stereo Fh22mar 616 51 076Family Handyman

Step 11

Apply the Speaker Cloth

  • Spread white craft glue evenly on the painted baffles.
  • Pay attention to the lines in the speaker cloth. Make sure they stay straight and square as you place the cloth on the baffle.
  • Place plywood on top to provide even pressure as the glue dries.
  • Trim the speaker cloth with a utility knife.

Console Stereo Fh22mar 616 51 081Family Handyman

Step 12

Cut the Slat Parts

  • Cut 2-in. x 16-1/2-in. blocks from 3/4-in. mahogany. This vintage stereo console needs eight.
  • Mill the rabbet on the ends of the stiles. Place the blank in the center portion of the jig (Photo 6A) and with a flat-top ripping blade set to 1/2-in. high, make multiple passes to cut the full width of the rabbet.
  • Make the first two angled cuts (Photo 6B) on each block. Clamp the stile blank in the jig. Make one cut and flip the blank over (Photo 6C) to make the second.
  • Flip the sled 180 degrees and make the second two angled cuts (Photo 6D) on each block, creating a slender chevron shape.

Console Stereo Fh22mar 616 51 011Family HandymanConsole Stereo Fh22mar 616 51 012Family Handyman  Console Stereo Fh22mar 616 51 013Family HandymanConsole Stereo Fh22mar 616 51 016Family Handyman

Step 13

Install the Speaker Baffles

  • To ensure a good fit, I made the speaker baffles slightly smaller than the opening. I attached them with glue and brad nails to mounting blocks on all four sides of the opening.

Console Stereo Fh22mar 616 51 083Family Handyman

Step 14

Assemble the Slats

  • I trimmed two slats flat on one edge and placed those on the left and right sides first. Then I attached the full slats that cover the joints between the veneered face and the speaker baffles.
  • Finally, evenly space the inner slats and pin them in place.

Stereo Console Fh22mar 616 51 087Family Handyman

Step 15

Cut and Rout the Legs

  • Make a routing template from 1/2-in. medium density fiberboard (MDF). Drill four evenly spaced holes in the template.
  • Trace the template on the sapele and rough-cut the leg with a band saw, staying about 1/8-in. away from the line.
  • I attached the routing template to the leg blanks with four small screws and cut it flush on the router table.

Console Stereo Fh22mar 616 51 063Family Handyman

Step 16

Attach the Legs to the Console

  • Using a 5/8-in. Forstner bit, drill 1/8-in. deep holes. This is the countersink for the washer-head screws.
  • Finish pre-drilling through the leg with a 5/16-in. drill bit. I centered each leg on the bottom of the console using a centering rule and set them two inches back from the front and back edges.
    • Pro tip: Face the side with the screw holes inward so they’re hidden underneath the console.

Console Stereo Fh22mar 616 51 091Family Handyman

Step 17

Finishing the Console

Console Stereo Fh22mar 616 51 093Family Handyman

Step 18

Upgrading the Audio Components

  • How you handle the audio upgrade can be simple or complicated.
  • I chose simple. I removed the original bits, then found a turntable ($200 at uturnaudio.com) to fit inside the narrow console, a Bluetooth-capable tube amp and a pair of bookshelf speakers from Dayton Audio ($150 and $130 respectively at parts-express.com).
  • Then I removed the old components and added a panel to hold the new pieces. And it sounds great!

Console Stereo Fh22mar 616 51 102 004 104 005Family Handyman