A garage door opener that hums or grinds but doesn't open the door may just have stripped gears-an easy, inexpensive repair. Use this guide to get your opener running again.
By the DIY experts of The Family Handyman Magazine
You might also like: TBD
If you press the garage door opener button and hear either a humming or a grinding sound, but the door won’t open, you may think you need a new opener. And you might. But before you give up on the old unit, pop off the cover and check for stripped gears. That’s a common problem and there is a garage door opener repair that you can do yourself for way less than the cost of a new opener.
You’ll have to get a replacement gear kit (two new gears, grease and washers), which may take some running around. But once you have the kit in hand, you can do the repair in about two hours. You’ll need a 2×4, a small drift punch, a standard 1/4-in. drive socket set, hex wrenches, a circular saw, a drill and a hammer. I’ll show you how to remove and replace the gears without damaging the shafts.
Start by unplugging the opener. Then remove the retaining screws for the metal cover and put it aside. Shine a flashlight directly at the gear set. If you see chewed-up teeth, you’ve nailed the problem. If the gears are in good shape, you’ve got a more serious problem and your best bet may be to just replace the entire unit. To find a replacement gear kit, write down the make, model and serial number of your opener (you’ll find it on a label on the back of the opener). Then call a garage door opener repair company. It’ll probably charge a bit more than an Internet site, but at least you’ll have the parts right away and be up and running the same day.
Getting out the gear shafts
Photo 1: Remove the chain
Unscrew the outer nut on the chain tensioning rod. If necessary, use pliers to prevent the chain from turning. Then slip on a pair of gloves and remove the greasy chain from the sprocket at the top of the opener.
Photo 2: Remove the helical gear assembly
Unscrew the hex-head screws that hold the helical gear assembly in place. Save the screws for reassembly. Then lift the entire assembly (sprocket, plate, shaft and helical gear) up and out of the top of the unit.
Use a combination wrench to loosen and remove the chain (Photo 1). Next, use a 1/4-in. drive socket, extension and ratchet to remove the helical gear assembly retaining screws (Photo 2). Take a digital photo of the wiring connections from the motor or label them with masking tape. Disconnect the motor wires and remove the entire motor assembly. Move the helical gear assembly and the motor assembly to your workbench.
Remove the helical and worm gears
Photo 3: Remove the helical gear from the shaft
Support both ends of the helical gear assembly with the two jigs. Hold a small drift punch over the roll pin and tap the pin out of the shaft with a small hammer.
Photo 4: Remove the worm gear
Loosen the collar setscrews with a hex wrench and slide the worm gear off the shaft. Then remove the motor retaining screws.
Cut a shallow groove into a 2×4 with a circular saw. Then slice off about a 3-in. section to make a jig to hold the helical gear assembly circular plate (Photo 3). Place the plate in the groove, hold the gear assembly level and mark the end of the shaft on another 2×4. Drill a hole in the wood and insert the end of the shaft. Then remove the roll pin (Photo 3). Slide the old gear off the shaft and replace it with the new gear. Reinstall the roll pin using the same jigs.
Next, remove the retaining collar and thrust washers on the end of the motor shaft (Photo 4). Pull the motor out of the chassis and slide the worm gear off the shaft (the roll pin stays in place on this shaft). Slide on the new worm gear with the notched end facing the roll pin.
Reassemble the motor assembly and place it back in the opener. Then install the helical gear assembly. Coat the gear teeth with new grease. Reattach the chain and tighten it to the proper tension (see your owner’s manual). Test your repair with the garage door disconnected from the opener trolley.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
You’ll also need gloves and a small drift punch
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.