How to Hang Drywall: Use a Lift

Updated: Feb. 05, 2024

Hang drywall alone with the right tools and techniques.

FH04FEB_DRYWAL_01-2Family Handyman

See easier ways to hang and handle drywall (aka Sheetrock). We have 10 tips that save time and strain, whether you're working alone or with a crew.

You might also like: TBD

Multiple Days

Rent a drywall lift for ceiling work

Photo 1: Load the lift

Flip down the support hooks to hold the sheet. Remember: the face of the sheet goes against the lift.

If you have to drywall a ceiling, don’t hesitate to rent a lift. It’s well worth the rental fee and is by far the best way to get a ceiling up without back strain. These five tools will making hanging drywall a lot easier.

Drywall lifts break down into three parts and fit easily into a midsize car. After you reassemble it, release the catch on the wheel and crank it up and down a few times to make sure it’s working smoothly. Then lock the lift and hoist one end of the drywall sheet up to the support hook—finish side down. Now lift the other end of the sheet up and slide it onto the second hook as shown. Lift slowly and smoothly—abrupt or jerky handling can pop the front edge of the drywall off the hook.

Tip the sheet so it’s horizontal and lock it down. Then wheel the lift into approximate position. Lifts are stable and maneuverable, so you can fine-tune the placement when you raise the drywall. Then crank it tight. You may need to get up on a ladder to nudge the sheet into place. Put in at least eight screws before lowering the lift.

Lifts work for walls, too

Photo 2: A lift makes wall work easier

Tip the sheet against the wall. Extend the support arms to suit 8 or 12-ft. sheets.

A lift works on upper wall sheets just as well as it does on ceilings. After loading the drywall, push the lift to the wall, position the sheet, tip the top edge against the wall and crank it snugly against the ceiling.

Make cutouts in place

Photo 3: Cut holes for ceiling lights

Run the cutout bit around the electrical box or light can. It’s the fastest, neatest way to cut holes!

Cutouts for lights and outlets are much faster and easier to make with the drywall in place, saving the trouble of taking the sheet down and recutting it if a precut hole doesn’t quite fit. Use a special cutout tool with a drywall bit, available at hardware and home centers. First, make sure to push electrical wires at least an inch back into the boxes, out of the way of the cutout bit. Next, measure and mark the approximate center points of the electrical boxes on the drywall, before you put it up. Crank the sheet up, and put in just enough screws to hold it in place, keeping the screws at least 12 in. from the cutout. Then punch the drywall cutout tool through the center mark and run it out to the edge until the bit hits the side of the box. Ease the bit up and over the edge to the outside of the can or box and slowly cut counterclockwise around it as shown. Drive nearby screws after the cutout is finished.

Panel rollers make big jobs small

Photo 4: Roll your rock

A panel roller lets one guy easily move two sheets at a time.

Have a few dozen sheets to move? Here’s the next best thing to having somebody carry the drywall for you: a heavy-duty panel roller that carries up to two sheets at a time (or anything else that’s flat and heavy). Roll drywall almost effortlessly through the house, using one hand to control the roller and the other to balance the sheet and steer around corners. The wheels tilt and roll over thresholds, and for bigger obstacles, just grasp the handle and lift the drywall. You can even tuck a sheet under your arm, a very simple and comfortable carrying position. This lifter doesn’t work on a full flight of stairs. Panel rollers are available at drywall and tool suppliers.

Ease the strain with a panel lifter

Photo 5: Carry rock comfortably

A panel lifter lets you lift and carry without the awkward arm-stretching and torso-twisting.

Take the strain off your arms and upper body and make navigating tight spots easier with a plastic panel lifter, available at home centers. Just hook the panel lifter around the bottom of the sheet at the center point, tip the sheet up and lift, leaving your lifting arm fully extended as if you were carrying a suitcase. Use your other arm to balance the sheet, keeping the drywall close to horizontal. You’ll be amazed—you can move drywall with half the effort. But it doesn’t work on full flights of stairs. Get a helper for that.

Preset nails (and use your head)

Photo 6: Set nails before you lift

With a few nails already in place, you won’t need a third hand to hang ceiling rock. Use your head to support the sheet, too.

When you need to hold a piece up in place without the lift, preset a half-dozen drywall nails around the edges at joist or stud locations before you lift the sheet. Hoist it up, support it tightly against the ceiling joists with a hand and your head (a sponge under the hat helps), then drive in the nails to hold the piece in place. Fasten it off with screws.

Customize the lift for angled pieces

Photo 7: Modify the lift

As with most things in life, all it takes is 2x4s and duct tape.

Modify the lift to hold small or irregular pieces by taping a pair of 2x4s perpendicular to the crossbars as temporary supports. The hooks won’t catch, so lock the crossbars down into the horizontal position.

Lever; don’t lift

Photo 8: Step and screw

Nudge the lower sheet against the upper sheet with foot power.

Photo 9: Roll lifter

A pry bar and block of wood will do the job, but this special tool is more convenient to use

Rather than straining to hold lower sheets up off the floor, lever them up snug against the upper sheet with a pry bar and a block of wood or a roll lifter (available at home centers).

Add nailers instead of recutting

Photo 10: Too long? No problem

No need to remove a too-long sheet—just add nailers so you can screw on the next sheet.

You’ve wrestled a heavy sheet up, put in half the screws and just noticed that you slightly miscut the sheet. Before you go through the hassle of taking the sheet down and recutting, try these possible fixes:

  1. Tack a 2×4 to the side of the joist as a nailer for the next sheet.
  2. Create a floating seam by screwing the unsupported end to a 1×4 that you slide on top of it. Let the 1×4 overlap the end about 1-1/2 in. Then screw the next sheet to the 1×4 as well. Cut the 1×4 longer than the piece you’re seaming so that adjoining sheets will help support it.

Measure tight but cut loose

Putting drywall up and then taking it down to shave an edge that won’t fit is a waste of energy. Instead, subtract 1/4 in. from your measurements to make up for rough cuts and wavy walls. It’s easier to fill slight gaps with joint compound than to struggle with a tight fit.

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

  • Chalk line
  • Drywall saw
  • Hammer
  • Safety glasses
  • Screw gun
  • T-square
  • Tool belt
  • Utility knife
You will also need a Drywall lift, Panel roller, Panel lifter, Cutout tool

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • Drywall nails
  • Drywall screws
  • Drywall sheets