How to Bend Wood with Steam

Updated: Nov. 04, 2022

A new woodworking skill, right around the bend!

Next Project
Time

Two days

Complexity

Advanced

Cost

$350

Introduction

Steam bending has long been employed to build boats, ships and wagons, even toboggans and snowshoes. A time-honored method of manipulating wood, steam bending will be a fun and rewarding addition to your woodworking skill set.

To begin your wood-bending experience, you’ll need a few basic items: an inexpensive steam generator, an easy-to-make plywood box and medium density fiberboard (MDF) to make a form. Bending wood takes patience and practice; a simple round mirror frame is the perfect place to start.

Tools Required

  • Cordless drill
  • Router (optional)
  • Steam Generator
  • Table Saw (or Circular Saw With Cutting Guide)

Materials Required

  • 2'x4' 3/4" Plywood
  • Bending Strap Clamp
  • Quarter-sawn oak or walnut
  • Round Mirror

Meet the Expert

Fh21djf 607 03 032 Courtesy Jay CorkFamily Handyman

Project editor Jay Cork has taught classes on bending wood with steam. Truly, no one is more full of hot air.

Fh23djf 622 53 056 1 How To Bend Wood With SteamFamily Handyman

How Does Wood Bend?

Fh23dja 622 53 045 0001 How To Bend Wood With SteamFamily Handyman

Some wood species — ash or oak, even cherry or walnut — can be bent by softening their lignin with heat. Think of lignin as the glue holding the wood fibers together. As the lignin and fibers are heated, they become pliable for a short time and the wood can be bent around a form.

Air-Dried is Best, But …

It’s a common misconception that only air-dried lumber bends well. I have found this to be only partly true. Kiln-dried lumber has a bad reputation because during the drying process, the lignin cooks and becomes stiff. If this happens, no amount of heat will bring it back.

Despite this risk, I’ve found kiln-dried wood can indeed be bent if it’s steamed for a longer period.

Project step-by-step (25)

Step 1

Build the Steam Chamber

Cut the box parts

Size the steam chamber to the parts being bent; any larger will waste heat energy. The box can be made from any wood — even PVC pipe!

  • Pro tip: I chose CDX ­(exterior) plywood because it’s cheap, easy to work with and holds heat better than PVC pipe.

Fh23dja 622 53 003 Fhm How To Bend Wood With SteamFamily Handyman

Step 2

Drill holes for support dowels

It’s important to suspend the wood inside the steam chamber to allow the heat to fully penetrate the full circumference of the wood inside. I used 3/8-in. dowels for this and drilled 13 holes, four inches apart.

  • Pro tip: Screw the two sides together while drilling so the holes align perfectly.

Fh23dja 622 53 004 How To Bend Wood With SteamFamily Handyman

Step 3

Assemble the box

Assemble the box with 1-1/2-in. screws.

  • Note: Make sure the holes for the support dowels are oriented near the bottom of both sides of the box.

Fh23dja 622 53 007 How To Bend Wood With SteamFamily Handyman

Step 4

Insert the support dowels

Cut the dowels to the width of the steam chamber. With the chamber on its side, guide the dowels into the holes, securing them with CA glue.

Fh23dja 622 53 010 How To Bend Wood With SteamFamily Handyman

Step 5

Add the legs

Adding legs provided space for the steam generator to sit underneath the steam chamber. I cut legs at a slight angle and attached them with 1-1/4-in. screws.

Fh23dja 622 53 011 How To Bend Wood With SteamFamily Handyman

Step 6

Drill holes for thermometers

Installing thermometers isn’t absolutely necessary, but having them lets you monitor the internal temperature, which should be a constant 220 degrees. I used two grill thermometers; the threaded neck made it easy to install each in the plywood box. Drill 1/2-in. holes and thread in the thermometers.

Fh23dja 622 53 015 How To Bend Wood With SteamFamily Handyman

Step 7

Drill the hose port

After shortening the hose, I drilled a 5/8-in. hole in the side of the steam chamber to accept the smaller, inner hose.

Fh23dja 622 53 030 How To Bend Wood With SteamFamily Handyman

Step 8

Make a simple lid

A single hinge on a plywood lid will suffice. I used a wood screw to keep the lid closed.

Fh23dja 622 53 Ta03 How To Bend Wood With SteamFamily Handyman

Step 9

Make the Bending Form

Rout the shape

The frame I’m bending for the mirror will form a partial circle. With a circle-cutting jig, cut the round shape with a plunge router.

  • Pro tip: Cut this in multiple passes with a 1/4-in. solid carbide spiral bit, going about 1/4-in. deeper on each pass.

Fh23dja 622 53 017 How To Bend Wood With SteamFamily Handyman

Step 10

Glue the form

Once the form has been routed, trace the outline on another piece of MDF. Cut out this part close to the line. I used a band saw, but a jigsaw works just fine. Glue and screw the two parts together and trim the excess flush with a router.

  • Pro tip: Once you glue the form together, drill evenly spaced holes around the circumference with a 2-in. Forstner bit. This provides space for the clamps needed to bend the wood. The edge of each hole should be 1-1/2-in. away from the edge of the form.

Fh23dja 622 53 019 How To Bend Wood With SteamFamily Handyman

Step 11

Attach the form to the base

When you’re attaching a bending form to an MDF base, there’s no such thing as too much glue or too many screws. Make it strong! After gluing the form to the base and allowing it to dry, I used 2-in. screws through the bottom to maximize its strength.

Fh23dja 622 53 024 How To Bend Wood With SteamFamily Handyman

Step 12

Add an anchor block

When bending wood, it’s important to anchor the wood firmly to the bending form. I prefer a lag bolt for this purpose.

Cut two lengths of hardwood to the same thickness as your workpiece plus the thickness of the backing strap. Drill a hole for the lag bolt in the longer piece and attach both to the form as shown using CA glue and 2-in. screws.

Fh23dja 622 53 032 How To Bend Wood With SteamFamily Handyman

Step 13

Bend the Wood

Drill anchor hole

With a 5/16-in. bit, drill a hole in one end of the bending stock to match the hole in the anchor block. When it comes time to bend, the lag bolt will go through this hole, anchoring the wood to the bending form.

Fh23dja 622 53 033 How To Bend Wood With SteamFamily Handyman

Step 14

Prepare the backing strap

I used a Veritas bending strap jig ($100 at leevalley.com). The strap that comes with the kit was 1-1/4-in. wide, but my stock was 1-1/2-in. wide, so I made my own backing strap. I used a rotary tool to cut it to length and drilled a hole in one to match the anchor hole in the wood.

Fh23dja 622 53 036 How To Bend Wood With SteamFamily Handyman

Step 15

Steam the wood

One rule of thumb says leave the wood in the steam chamber for one hour per inch of thickness. This assumes you’re using air-dried lumber with a moisture content of more than 20 percent. Kiln-dried lumber should be steamed for twice that long. This 1-1/4-in. thick, kiln-dried walnut steamed for two hours.

Fh23dja 622 53 039 How To Bend Wood With SteamFamily Handyman

Step 16

Work fast!

Once the wood comes out of the steam chamber, quickly get it on the form and start the bending process. You have less than two minutes before the lignin cools and starts to reset.

Fh23dja 622 53 042 How To Bend Wood With SteamFamily Handyman

Step 17

Clamp as you go

Here’s where a helper comes in handy! As you pull the wood around the form, have someone follow you, tightening clamps against the form as you go.

Fh23dja 622 53 048 How To Bend Wood With SteamFamily Handyman

Step 18

Complete the Mirror Frame

Cut the rabbet

On a router table, cut a 1/2-in. wide by 1/4-in. deep rabbet around the back of the curved frame. This will ­provide plenty of room for the thickness of the mirror and the adhesive to keep it in place.

Fh23djf 622 53 059 How To Bend Wood With SteamFamily Handyman

Step 19

Profile the frame

Here’s where you let your creative side take over. Profile the frame in any way you find appealing. I rounded over the inside edge with a 1/4-in. round-over bit and the outside edge with a “tabletop” bit — a slightly oblong round-over.

Fh23djf 622 53 062 How To Bend Wood With SteamFamily Handyman

Step 20

Apply a finish

Apply the stain and finish of your choice. I used iron oxide stain and shellac. The iron oxide will turn the wood almost black without obscuring the grain, and the shellac dries really fast.

Fh23djf 622 53 065 How To Bend Wood With SteamFamily Handyman

Step 21

Attach a hanger

Because I chose an acrylic mirror, not glass, I felt comfortable gluing the hanger right to the back with construction adhesive. It doesn’t even have to be perfectly ­centered. The frame is round, so there’s no perfect up or down.

Fh23djf 622 53 067 How To Bend Wood With SteamFamily Handyman

Step 22

Set the mirror

After the finish dries, set the frame face down on a workbench. Place the mirror in the rabbet and glue it in place with construction adhesive.

Fh23djf 622 53 070 How To Bend Wood With SteamFamily Handyman

Step 23

Shopping for materials

You can find steam generators at woodworking outlets like Rockler or Woodcraft, but big box stores sell them, too, as wallpaper steamers. (They’re the same thing.) I purchased my Wagner model at The Home Depot.

Step 24

Figure B: The Bending Form

What is springback?

When wood is bent, it has a natural tendency to return to its original shape. It will never go back to straight, but it will “spring back” a little. To compensate for springback, undersize your form by roughly 10 percent. The mirror I chose for this project has a 17-in. diameter, so I cut my form with a diameter of 15-1/4-inches.

Fh23dja 622 53 Ta02 How To Bend Wood With SteamFamily Handyman

Step 25

Leave it alone

In general, allow the wood to sit in the form for 12 hours before removing it. If you’re making many parts and want to speed things up, you can make a frame to hold the now-bent piece of wood. After letting it cool for an hour or so in the form, transfer it to the frame. Then your form is freed up, ready for another part to be bent.