Stop Leaks in Plumbing Joints

Foolproof methods for connecting valves, faucets and sinks, and drain parts.

Next Project

Introduction

The best time to fix a plumbing leak is before it happens, by properly connecting water supply and waste line fittings. Learn the tricks that pros use to make leakproof connections.

Tools Required

  • Adjustable wrench
  • Slip joint pliers
  • Wrench set

Materials Required

  • Flexible supply tubes
  • Teflon pipe joint compound
  • Teflon tape

Project step-by-step (11)

Step 1

Use two types of Teflon pipe joint compound on threaded joints

Wrap threads with plumbers tape

WrapFamily Handyman

Wrap the plumbers tape around the pipe clockwise.

How to Fix a Dripping Shower

Step 2

Add pipe joint compound

compoundFamily Handyman

Smear a little pipe joint compound on the plumbers tape.

Top 10 Plumbing Fixes You Can Do Yourself

Step 3

Tighten the connection

TightenFamily Handyman

Using two wrenches, tighten the connection over the joint compound and plumbers tape.

Why use plumbers tape and pipe joint compound

Connections that rely on threaded pipes and fittings are prone to leaks if they’re not sealed with either Teflon tape or Teflon pipe joint compound. Careful plumbers use both pipe joint compound and teflon on every joint for extra security. They don’t want to come back.

Start by wrapping the male threads with Teflon tape (Photo 1). With the end of the threaded pipe facing you as shown, wrap the plumbers tape clockwise. Usually three layers is enough. Once in a while, you’ll run into a loose fitting that requires four or five wraps. Stretch and tear the tape to complete the wrap.

Spread a thin layer of Teflon pipe joint compound over the tape (Photo 2). If you’re working with plastic pipe, choose Teflon pipe joint compound that’s compatible with it. Then start the threads by hand before tightening the connection with wrenches (Photo 3). Wipe away the excess pipe joint compound.

Well Pump Troubleshooting and DIY Repair

Step 4

Lubricate the ferrule on compression joints

Wipe pipe joint compound

WipeFamily Handyman

Lubricate the ferrule and brass ring with pipe joint compound.

Handy Plumbing Tips and Tricks

Step 5

Thread on valve pipe joint compound

pipeFamily Handyman

Pipe joint compound helps the brass ferrule seal to the valve.

The 10 Most Common Plumbing Mistakes DIYers Make

Step 6

Tighten the fitting

fittingFamily Handyman

Tighten the compression fitting. The pipe joint compound provides a greater margin of safety. Compression joints are most common on shutoff valves, although you find them on other fittings as well. They have a brass or plastic ring (ferrule) that’s compressed into a recess when you tighten the nut, forming a seal. Lubricating the pipe and the ferrule with a bit of Teflon pipe joint compound (Photo 1) helps the ferrule slide along the pipe and squeeze tightly into the recessed fitting with less wrench pressure (Photo 2). Tighten compression fittings firmly with two wrenches to crimp the ferrule onto the pipe (Photo 3). Also make sure the pipe or tube goes straight into the fitting. Misalignment will cause a leak. If the fitting leaks after you turn on the water, try tightening the nut an additional one-quarter turn. This usually stops the leak.

Step 7

Align slip joints precisely for a tight seal

Lubricate pipe

LubricateFamily Handyman

Pipe joint compound helps lubricate and seal waste line connections.

100 Plumbing Goofs and Other Scary Stuff

Step 8

Assemble and align

alignFamily Handyman

Hand-tighten all the joints, then align and lock the pipes in position with a slip joint pliers

Joints on chrome trap assemblies rely on rubber slip joint washers for the seal, which often leak. If you’re reassembling a chrome trap, buy new slip joint washers and nuts. However, new washers sometimes stick to the pipe, causing them to twist or distort as you push them tight with the slip joint nut. To avoid this, lubricate the drain tubing and slip joint with a little pipe joint compound (Photo 1). The compound helps the washer slide smoothly and creates a tighter seal.

Start the slip joint nut by hand, and twist it on until the threads are engaged correctly. Hand-tighten all joints first (Photo 2). Then adjust the trap parts until they’re aligned and pitched slightly for drainage. This is key; a misaligned joint will leak, even with new washers. Finally, use a large slip joint pliers to tighten the nuts an additional half turn.

Plastic trap parts use hard plastic slip joint washers for a seal. Make sure the flat part is against the nut with the tapered side facing the fitting.

12 Things Your Plumber Doesn’t Want You To Know

Step 9

Choose flexible supply tubes

Solid copper supply lines

copperFamily Handyman

Avoid solid copper or chrome supply lines. They’re difficult to get right unless you’ve had lots of experience with them.

12 Things Your Plumber Wants You To Know

Step 10

Flexible lines

linesFamily Handyman

Braided, flexible supply lines are almost foolproof and don’t require any measuring and cutting.

Step 11

Close-up of gasket

gasketFamily Handyman

Flexible supply lines use rubber gaskets to seal the connections, and usually just need hand-tightening plus half a turn with a wrench

The skinny copper or chrome supply tubes used to connect faucets and toilets (Photo 1) are tricky to cut, bend and align. But you don’t have to put up with them. When you’re replacing a faucet or toilet, use flexible supply hoses with a braided covering instead (Photo 2). They have rubber gaskets at each end and don’t require much force to seal. They’re available in many lengths and are flexible enough to fit almost any configuration. The only trick is buying a connector with the correct size nuts on the ends. Take your old tubing and the nuts on each end along with you to the store to be sure of an exact match.

Start the nuts carefully and hand-tighten. Then tighten an additional half turn (Photo 2). Avoid overtightening. It’s easy to tighten the nuts a little more if the joint leaks. Find and repair hidden plumbing leaks.