Start with the retaining nut, then look for other problems
Photo 1: Tighten retaining nut
If you’re lucky, you can fix your leaking faucet by simply tightening the nut under the handle. Don’t crank it hard, though. If snugging it up doesn’t solve the problem, turn off the water and remove the nut to repair the faucet.
Photo 2: Remove the stem
Next, remove the faucet stem. It’s easier if you reinstall the handle temporarily so you’ll have something to grip. You may have to turn the handle to unscrew the faucet stem to get it to come out.
Photo 3: Replace washer assembly
Keep track of the parts as you disassemble the faucet so you can install the new ones in the same order.
Photo 4: Remove the vacuum breaker cap
Pop off the vacuum breaker cap to access the parts underneath. Pry from both sides with a pair of screwdrivers.
Photo 5: Vacuum breaker parts
Unscrew the retainer and pull out the vacuum breaker. You may be able to fix the leak by simply cleaning the parts and reinstalling them. If this doesn’t work, take the parts to the store to find replacement parts.
Leaky, dripping exterior faucets not only waste water but also dump it next to the foundation, right where you don’t want it. Luckily, they’re easy to fix. If you have a frost-proof faucet like the one we show here, check out these fixes for the most common problems.
If the faucet leaks from around the handle just when the water is turned on, the stem packing may be leaking. In some cases, you can fix this by simply tightening the retaining nut that’s under the handle. Remove the screw in the center of the handle and pull the handle off. Try tightening the nut slightly (Photo 1). You’ll have to experiment to see which direction to turn the nut, since some faucets have reversed threads that tighten counterclockwise.
If simple tightening doesn’t solve the problem, you’ll have to remove the faucet stem (Photo 2) and replace the packing gasket. Turn off the water to the exterior faucet by locating the valve inside the house and closing it (or the main water valve). Buy a repair kit that matches your faucet brand and use the packing from the kit. If your faucet still leaks, the stem may be leaking and you should replace the faucet.
If your faucet leaks out of the spout when it’s turned off, the washer is bad. On frost-proof faucets, the washer is located on the end of the long faucet stem. Remove the handle and nut (Photo 1) and pull the stem from the faucet (Photo 2). You may have to turn the stem to “unscrew” it before it’ll come out. Getting the faucet apart is the hard part. After that, you simply replace the old parts with new ones. Pay close attention when you take the parts off (or snap a photo) so you can put the new ones back the same way. Snap off or unscrew the washer assembly and replace it (Photo 3). Then reassemble the faucet in the reverse order. If you find that the faucet starts leaking again after a short time, the valve seat is worn and you should replace the entire frostproof faucet. If the faucet is attached with threads, you can simply turn off the water, unscrew the faucet and replace it with one that’s the same length. If it’s soldered on, you’ll have to break out your torch and soldering tools.
Most frost-proof faucets have a built-in vacuum breaker located on top of the faucet (Photo 4). If you see water dribbling out from under the cap when the water is running, it’s leaking. Photos 4 and 5 show how to replace a leaking vacuum breaker. Some repair kits include the parts for this. If not, you’ll have to purchase them separately.
Required Tools for this frost free hose bib Project
Have the necessary tools for this DIY frost free hose bib project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Adjustable wrench
- Slip joint pliers
Required Materials for this frost free hose bib Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Replacement vacuum breaker parts
- Washer assembly