Video: How to Mix Concrete
Gary Wentz, senior editor at The Family Handyman, will show you how to mix concrete. These hints and tips will save you time and energy.
Overview: Materials and Tools
Protect your skin and eyes! The cement in concrete is caustic and can cause burns if it gets on your skin.
Mixing bags of concrete isn’t complicated. You add some water, stir it up and pour it out. But to get the most strength from the concrete, you have to recognize when it has just the right amount of water mixed in. Too little water and the particles in the mix won’t stick together. Too much water weakens the concrete. In this article, we’ll show you what the perfect mix looks like. We’ll also show you a mixing technique that will ensure thoroughly mixed concrete with a minimum of effort.
For most small jobs around the home, bagged concrete mix is the most convenient and least expensive way to go. You can use it for fence post footings, deck footings and even small concrete pads. For jobs requiring more than about 30 bags, consider ordering “ready-mix” concrete from a truck instead.
Sixty- or 80-lb. bags of concrete mix are readily available at home centers, lumberyards and hardware stores. Don’t confuse concrete mix with sand mix or mortar mix. They don’t contain the aggregate (stones or gravel) that’s necessary to make a pour thicker than about 3/4 in. You’re likely to find more than one kind of concrete mix on the shelf, including “fast setting,” “high early strength” and “fiber reinforced.” But for most jobs, standard concrete mix is fine. Read the recommendations on the bags or check manufacturers’ Web sites to find out if one of the special mixes would work better for your project.
Whether you handmix concrete in a plastic tub, homemade mixing tub or wheelbarrow, the technique is the same. However, it’s easier to move and dump concrete that’s mixed in a wheelbarrow. For larger jobs, you could rent a mixer ($35 per day), but it may be more economical to simply order ready-mix concrete. In addition to a mixing container, you’ll need a sturdy hoe and a large bucket as well as a stiff-bristle scrub brush to clean the equipment. Wear waterproof gloves and safety glasses because the cement mixing in the concrete mix is caustic and can burn skin. Wash it off with water if it gets on your skin.
Step 1: Add water to the dry mix
Photo 1: Slice and dump the bag
Set the bag of concrete mix in one end of the wheelbarrow and slice it open with your hoe. Dump the mix from the bag and pull out the paper bag.
Photo 2: Add a measured amount of water
Fill a bucket with the specific amount of water recommended on the bag (amount varies with bag size). For future reference, mark the water level with a permanent marker. Pour the water into the opposite end of the wheelbarrow, reserving about 4 cups to add later if needed.
Photo 3: Gradually wet the mix
Pull a small amount of the dry mix into the water with a hoe and mix it completely. Continue pulling and mixing until all of the powder is wetted and the mix is piled at your end of the wheelbarrow. Continue mixing by going to the other end of the wheelbarrow and pulling the mix back toward you.
One of the most common mistakes beginners make is to add too much water and end up with concrete that’s thin and soupy. Here are a few tips to avoid the problem.
First, pour a measured amount of water into the mix from a bucket rather than squirting it in with a hose (Photo 2). Continue mixing for a few minutes after all the water is absorbed because the concrete will often get soupier as you mix. If you add more water right away, it may end up runnier than you’d like. Finally, keep at least a few cups of dry concrete mix handy just in case your mix gets too thin.
A hoe makes a great mixing tool. A flat shovel or spade works too. Whichever you choose, it’s best to add the water to one end of the wheelbarrow or mixing tray and pull the dry mix into it a little at a time (Photo 3). This method ensures that all the dry particles are completely wetted.
Use a sturdy wheelbarrow to mix your concrete. And make sure it’s on a level surface. Brace the wheelbarrow with your knee when you’re mixing from the side.
Step 2: Work it to the perfect consistency
Photo 4: Too dry
Drag the hoe through the mix to make a trough. The mix is too dry if the sides of the trough are crumbly and the concrete falls in chunks when you disturb it. Add water one cup at a time, mixing between each addition.
Photo 5: Too runny
Add more dry concrete if the mix is too wet and soupy and sags into the trench.
Photo 6: Just right
The mix is just right when the sides of the trough stand and the ingredients are thoroughly wetted. A hoe patted against the concrete will leave a slightly shiny surface.
If the mixed concrete looks like the mix in Photo 6, it’s ready to pour. Otherwise, mix in additional dry mix or water until you get the right consistency.
It’s tempting to just squirt water into the dry concrete mix with a hose and mix up a soupy batch of concrete. After all, it’s quicker and the runny concrete is easier to pour. The trouble is, soupy concrete is only about half as strong as a proper mix and is more likely to crack. That’s why we recommend spending a little extra time measuring the water into a bucket first, and adding only as much as is needed. Even though the thicker mix is a little harder to place, it’ll be worth the extra effort.
Step 3: Clean up promptly
Photo 7: Wash your tools
Scrub the wheelbarrow and tools with a stiff-bristle brush before the concrete starts to harden. Rinse well.
Remember to clean your equipment right away (Photo 7). Once the concrete hardens, it’s a bear to get off. Scrape excess concrete from the wheelbarrow and pile it on a piece of plastic. If it’s a big pile, break it up into manageable chunks before it fully hardens. Dump the rinse water in an inconspicuous corner of your lot (it can kill grass). You can even dig a depression to contain the water and then cover the residue after the hole drains.
What’s the Best Type of Bagged Concrete to use for a Walkway?
“If you want to get your walkway back into service fast,” says concrete expert Frank Owens, “your best choice is ‘high early strength’ concrete.” This type of concrete has a higher percentage of cement in the blend so it sets up faster than standard concrete mix. You can walk on it within 10 to 12 hours, compared with several days.
It also generates more heat than standard bagged concrete mix, which means you can tackle your walkway project earlier or later in the season, in temperatures as low as 35 degrees F, with less chance of setting and hardening problems.
However, if your walkway has many steps or landings with exposed edges, Owens recommends fiber reinforced crack-resistant concrete mix. It contains thousands of little plastic fibers to make it more resistant to shrinkage cracks, edge chipping, impact damage and scaling during freeze/thaw cycles. Crack-resistant concrete takes three days to set up, so your walkway will be out of commission that long, but it can make concrete steps more durable under harsh conditions.
“The right concrete for a project is a matter of tradeoffs,” Owens says. “Consider setup speed, surface durability and the amount of weight the surface will bear.” No matter which product you choose, Owens recommends using as little water as possible. “The lower the water-to-cement mixing ratio, the stronger the concrete and the better the shrinkage resistance.”
Editors’ Note: Visit quikrete.com for an excellent comparison of bagged concrete choices and to check out its video library of tips and techniques for working with concrete.
Meet the Expert
Frank Owens has more than 28 years of experience in the concrete industry and has been with The Quikrete Companies for the past 25 years.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Dust mask
- Safety glasses
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 60- or 90-lb. sack