Save on Pinterest

Swing-out Storage Kitchen Cabinets

Triple your cabinet space!

FH18DJF_583_00_015 swing-out storage kitchen cabinetFamily Handyman
If your wall cabinets are so full that you can’t find anything without constant reshuffling, we have the perfect solution. This swing-out cabinet provides two extra layers of shelving for great visibility and easy access. We chose to make shallow shelves on the front for spices and wider shelves on the back for bottles or cans, but you can configure your swing-out however you like. Narrow adjustable shelves behind the swing-out provide even more storage space.

You might also like: TBD

Time
One day
Complexity
Beginner to intermediate
Cost
$110 depending on size

FH18DJF_583_00_015 swing-out storage kitchen cabinetFamily Handyman

Tools and materials for swing-out storage

You’ll find all the materials for this swing-out storage cabinet at home centers or lumberyards. The plywood has to be cut accurately into the parts for the swing-out storage, and the 1x3s ripped into 1-in.-wide strips for the shelf edging. A table saw and power miter saw are the best tools for these cuts.

We used an 18-gauge brad nailer and 1-1/2-in. brad nails to connect the parts. But if you don’t own a brad nailer, you can use screws or drive finish nails by hand.

FH18DJF_583_00_023 swing-out storage cabinet kitchen spice rackFamily Handyman

3 tiers of shelving

Keep your most-used spices on the front shelf for instant access. The two inner shelves are perfect for items you use less often.

Plan the swing-out size

Since there are so many different sizes of wall cabinets, we can’t give you an exact plan for building a swing-out to fit in yours. However,  since most wall cabinets are about the same depth, you should be able to make the cabinet 8 in. deep like ours, and you’ll only need to adjust the width and height to fit.

Project Directions:

FH18DJF_583_50_018 measure cabinetFamily Handyman

1. Measure your cabinets

Start by measuring the height of the opening (Photo above) and recording the measurement. Subtract 1/2 in. from the height to determine the height of the shelf unit. Also measure the narrowest width from protruding hinges or door parts.

FH18DJF_583_50_024 cabinet width cardboard templateFamily Handyman

2. Check for clearance

Determining the width is trickier because you have to subtract from the width measurement to compensate for the diagonal width of the swing-out storage cabinet. There are formulas you can use, but it’s easier to simply make a cardboard template and adjust the size until it fits. Cut a piece of cardboard 8 in. wide and 2 in. shorter than the width of the cabinet and see if it fits diagonally (Photo above). Trim the cardboard until you have about 1/2-in. clearance. Now measure the cardboard and subtract 1-5/8 in. to determine the length of the top and bottom. Check out Figure A in Project PDFs below for top and bottom swing-out measurements (Labeled “B” in Cutting List, also below).

FH18DJF_583_50_003 build a cabinet Family Handyman

3. Build a box

Start by cutting out the sides, top and bottom and nail and glue them together (Photo above). If you use screws rather than nails, you can skip the glue. Next, determine your shelf spacing and nail in the shallow shelves (Labeled “C” in Cutting List). Leave enough space for your tallest spice containers. We spaced our shelves about 5-1/2 in. apart.

FH18DJF_583_50_007 build swing-out cabinetFamily Handyman

4. Install the divider

Next, measure the inside height and width dimensions and cut the interior plywood divider (Labeled “D” in Cutting List) to fit. Press the divider against the shallow shelves and nail through the sides to hold it in place (Photo above). Flip the carcass over and measure from the face of the divider to the edge of a side to determine the width of the deeper shelves (Labeled “E” in Cutting List) on the back of the swing-out storage. We added two shelves, leaving one tall space for bottles, with two shorter spaces above. If you have a lot of bottles, you could simply divide the space in half and install only one shelf. Cut the shelves to fit and nail them in.

FH18DJF_583_50_009 drill for rodsFamily Handyman

5. Drill holes for the rods

When the plywood carcass is finished, install the 1-in.-wide solid wood edging. After ripping the boards to 1 in. wide, cut the vertical pieces (Labeled “F” in Cutting List) to length, mark the hole locations and drill holes for the rods (Photo above).  Set one edging piece on the swing-out and mark the rod positions 2 in. above each shelf. Drill 1/4-in. holes in the center of the edging at each mark. Use this as a pattern to mark and drill the opposite edging piece.

FH18DJF_583_50_012 swing-out storage cabinetFamily Handyman

6. Add the edging and rods

Then nail the vertical edging pieces to the carcass, letting them hang over the outside edge about 1/16 in. (the width of a quarter; Photo above). Cut the horizontal edging pieces to fit between the vertical pieces and nail them in. Install these with the bottom edges flush to the plywood to create a 1/4-in. lip on the top of the shelf. Repeat this process on the opposite side to complete the swing-out construction.

FH18DJF_583_50_014 swing-out attach continuous hingeFamily Handyman

7. Apply Finish and attach the continuous hinge

We used spray cans of polyurethane to finish our swing-out before installing it. Cover the aluminum rods with masking tape. Then apply several light coats, sanding the dried polyurethane with 400-grit sandpaper between coats. After you are done with the finish, cut a continuous hinge to the height of your swing-out cabinet with a hacksaw. Determine which side of the swing-out is opposite the cabinet door and mount the hinge to this side (Photo above).

FH18DJF_583_50_026 install the swing-outFamily Handyman

8. Hang the swing-out

Prop up the swing-out so that there’s equal space on the top and bottom. Align the continuous hinge with the front of the hinge pin (the rod-shaped center section) flush to the cabinet face. Attach the hinge with the small screws provided.

FH18DJF_583_50_035 add adjustable shelves to a cabinetFamily Handyman

9. Add adjustable shelves

Install shelves at the back of the cabinet. Measure the depth of the cabinet and subtract 8-1/4 in. to determine the depth of the shelves. Subtract 3/4 in., the thickness of the edging, from this dimension to determine the width of the plywood sides and shelves.

Cut two strips of plywood for the sides, and cut as many shelves as you want. Cut the side supports (Labeled “H” in Cutting List) to fit top to bottom in the cabinet. Then drill a series of 1/4-in. holes in the plywood sides for shelf pins. Use a shelf-pin jig or a strip of pegboard with 1/4-in. holes as a drilling guide.

Figure B (in Project PDFs below) shows how to install the edging pieces on the shelves and side pieces. Finish up by screwing the side shelf supports to the sides of the cabinet and installing the shelves. Mount a magnetic catch to the top of the wall cabinet to hold the swing-out in place.

For more kitchen organization ideas click here.

Project PDFs

Click the links below to download the materials and cutting lists for this project. As well as the projects construction drawings.

Cutting List and Project Drawings — Figure A & B

Materials List