Pots and pans
Build wide rollout trays for pots and pans.
Used narrow rollouts in pantry cabinets or cabinets with center dividers.
Wastebasket rollouts are basically standard rollout drawers hung upside down, with cutouts for baskets.
Base cabinets have the least convenient storage space in the entire kitchen. To access it, you have to stoop way over or even get down on your knees and then sort through all the stuff in front to find that particular omelet pan or storage container. What a pain. Rollouts solve that problem. They make organizing and accessing your cabinet contents back-friendly and frustration free.
If you’re stuck with cabinets without rollouts, don’t despair. In this article, we’ll show you how to retrofit nearly any base cabinet with rollouts that’ll work as well as or better than any factory-built units.
It’s really very easy. Once you take measurements, you can build the rollout drawer (Photos 2 – 6), its “carrier” (Photos 7 – 9), and attach the drawer slides (Photos 6 and 7), all in your shop. Mounting the unit in the cabinet is simple (Photos 10 – 13). We’ll also show you how to construct a special rollout for recycling or trash (Photos 14 – 16).
The project will go faster if you have a table and a miter saw to cut out all the pieces. A circular saw and cutting guide will work too; it’ll just take a little longer. You can build a pair of rollouts in a Saturday morning.
What wood products to buy
Our rollout drawers are entirely made of 1/2-in. Baltic birch plywood. Baltic birch is favored by cabinetmakers because it’s “void free,” meaning that the thin veneers of the plywood core are solid wood. Therefore sanded edges will look smooth and attractive. If your home center doesn’t stock Baltic birch, you can find it at any hardwood specialty store (search online or look under “Hardwood Suppliers” in the yellow pages to find a source). Baltic birch may only come in 5 x 5-ft. sheets, so don’t expect to fit it in your minivan. But home centers often carry smaller pieces. Baltic birch plywood may not even be labeled as such at the home center. But it’s easy to recognize by comparing it with other hardwood plywood in the racks. Baltic birch will have more and thinner laminations in the plywood core.
If you choose, you can make the sides of the rollout drawers from any 1×4 solid wood that matches your cabinets and then finish to match (use plywood for the bases). But if you use 3/4-in. material for the sides, subtract 3 in. from the opening to size the rollout (not 2-1/2 in., as we describe in Photo 2).
The drawer carriers (Figure A) are made from pine 1x4s for the sides (Photo 7) and 1/4-in. MDF (medium density fiberboard) for the bases (Photo 9). The MDF keeps the drawer base spaced properly while you shim and attach it to the cabinet sides. It can be removed and reused for other carriers after installation. If MDF isn’t available, substitute any other 1/4-in. hardboard or plywood you wish.
Side-mounted slides are the best choice among drawer slide options. Their ballbearing mechanisms and precise fit make for smooth-operating drawers that hold 90 lbs. or more. We used 22-in. full-extension side-mount drawer slides that have a 90-lb. weight rating. That means they’ll be sturdy enough even for a drawer full of canned goods. Full-extension slides allow the rollout to extend completely past the cabinet front so you can access all the contents. Slides are available at any home center or well-stocked hardware store.
Rollout Construction Details
Use these basic plans to construct any width of rollout. Construction is similar for the standard and wastebasket rollouts—the wastebasket rollout is just a standard rollout flipped over.
Measure carefully before you build
Photo 1: Measure twice
Open the cabinet doors to their widest point and measure the narrowest part of the cabinet opening (usually at the hinges).
Photo 2: Cut the drawer sides
Rip 1/2-in. plywood down to 3-1/2 in. wide and cut two 22-in. lengths (drawer sides) and two more to the measured width minus 2-1/2 in. (drawer front and back; Figure A).
Photo 3: Set up an assembly jig
Clamp or screw two straight 24-in. 2x4s to the corner of a flat surface to use as an assembly jig. Use a carpenter’s square to ensure squareness. Leave a 2-in. gap at the corner.
Nearly all standard base cabinets are 23-1/4 in. deep from the inside of the face frame (Photo 1) to the back of the cabinet. So in most cases, 22-in. long rollout drawer and carrier sides will clear with room to spare. Check your cabinets to make sure that 22-in. rollouts will work. If you have shallower cabinets, subtract whatever is necessary when you build your rollouts and their carriers (see Figure A).
Then measure the cabinet width. The drawer has to clear the narrowest part of the opening (Photo 1). When taking this measurement, include hinges that protrude into the opening, the edge of the door attached to the hinges, and even the doors that won’t open completely because they hit nearby appliances or other cabinets. Plan on making the drawer front and rear parts 2-1/2 in. shorter than the opening (Figure A).
We show drawers with 3-1/2-in.-high sides, but you can customize your own. Plan on higher sides for lightweight plastic storage containers or other tall or tippy items, and lower sides for stable, heavier items like small appliances.
Drawer slides aren’t as confusing as they seem
Photo 4: Assemble the sides
Spread woodworking glue on the ends and clamp a drawer side and front in place, then pin the corner together with three 1-1/4-in. brads. Repeat for the other three corners.
Photo 5: Nail the drawer bottom
Cut a 1/2-in. plywood bottom to size. Apply a thin bead of glue to the bottom edges, and nail one edge of the plywood flush with a side, spacing nails every 4 in. Then push the frame against the jig to square it and nail the other three edges.
Photo 6: Screw on the drawer side of the slide
Separate the drawer slides and space the drawer part 1/4 in. up from the bottom. Hold it flush to the front and screw it to the rollout side.
Photo 7: Mount the carrier side of the slide
Mount the carrier part of the drawer slide flush with the bottom and front of the carrier sides.
At first glance, drawer slides are pretty hard to figure out, but after you install one set, you’ll be an expert. They’re sold in pairs and each of the pairs has two parts. The “drawer part” attaches to the rollout while the “cabinet part” attaches to the carrier. To separate them for mounting, slide them out to full length and then push, pull or depress a plastic release to separate the two parts. The release button position and shape vary among manufacturers, but if you look at the directions, you’ll be able to figure it out. The cabinet part, which always encloses the drawer part, is the larger of the two, and the mounting screw hole locations will be shown in the directions. (Screws are included with the drawer slides.) The oversized holes allow for some adjustment, but if you follow our instructions, you shouldn’t have to fuss with fine-tuning later. When mounting the slides, you should make sure to hold them flush with the front of the rollout drawer and carrier sides (Photos 6 and 7). The front of the drawer part usually has a bent metal stop that faces the front of the drawer.
Assembling parts and finishing the rollouts
Photo 8: Measure the carrier bottom
Slide the drawer and carrier sides together and measure the carrier width. Cut 1/4-in. MDF to that width and 1 in. less than the carrier depth (usually 21 in.).
Photo 9: Nail the carrier bottom
Rest the carrier assembly on 3/4-in.-thick spacers, pull the carrier sides slightly away from the drawer, then nail on the carrier bottom (no glue).
Photo 10: Measure for spacers
Remove the drawer, tip the carrier into the cabinet and push the carrier against one side. Measure the gap and rip six 3-1/2-in.-long spacers to half of the thickness.
Photo 11: Attach the carrier sides
Nail the spacers to the center and each end of the carrier sides (not into the cabinet; see next photo). Then predrill and screw the carrier sides to the cabinet in the center of each shim. Slide the drawer back into place.
Close up of spacers
Nail the spacers to the sides.
Photo 12: Install the upper rollout
Cut plywood spacers to temporarily support the upper rollout and set them onto the carrier below. Rest the second carrier on the spacers and install it as shown in Photo 11.
It’s important to build the rollout drawers perfectly square for them to operate properly. Photos 3 and 4 show a simple squaring jig that you can clamp to a corner of any workbench to help. Use the jig to nail the frame together, but even more important, to hold the frame square when you nail on the bottom panel. If it hangs over the sides even a little, the drawer slides won’t work smoothly.
Use 1-1/4-in. brads for all of the assembly. Glue the drawer parts together but not the bottom of the carrier. It only serves as a temporary spacer for mounting. (After mounting the carrier and drawer, you can remove it if it catches items on underlying drawers or even reuse it for other carriers.) If you’d like to finish the rollout for a richer look and easier cleaning, sand the edges with 120-grit paper and apply a couple of coats of water-based polyurethane before mounting the slides.
To figure the spacer thickness, rest the lower carrier on the bottom of the shelf, push it against one side of the cabinet and measure the gap on the other (Photo 10). Rip spacers to half that measurement and cut six of them to 3-1/2 in. long. Slip the spacers between both sides of the carrier to check the fit. They should slide in snugly but not tightly. Recut new spacers if you have to. In out-of-square cabinets, you may have to custom-cut spacers for each of the three pairs of spacers, so check each of the three spacer positions. It’s easiest to tack the spacers to the rollouts to hold them in place before predrilling 1/8-in. holes and running the screws through the rollout frames and spacers and into the cabinet sides (Photo 11).
Slip the rollout into its carrier and check for smooth operation. If you followed the process, it should work perfectly. If it binds, it’s probably because the spacers are too wide or narrow. Pull out the carrier, remove the spacers and start the spacer process all over again. The best way to level and fasten the upper rollout is to support it on temporary plywood spacers (Photo 12). We chose to cut pieces of plywood 7 in. high. In reality, the exact height is up to you. If, for example, you want to store tall boxes of cereal on the bottom rollout and shorter items on the top, space the top rollout higher. You can even build and install three or more rollouts in one cabinet for mega storage of short items like cans, cutlery or beverages. (Those now-obsolete shelves you’re replacing with rollouts are good stock to use for your spacers.) Again, pin the spacers in place with a brad or two to hold them while you’re predrilling and screwing the carriers to the cabinet sides. Be sure to select screw lengths that won’t penetrate exposed cabinet sides! In most cases, 1-5/8 in. screws are the best choice. Strive for 1/2-in. penetration into the cabinet sides. Countersink the heads as far as necessary to get the proper penetration.
Building Rollouts in Cabinets with Center Dividers
Many two-door cabinets have a center divider, which calls for a slightly different strategy. You can still build rollouts, but they’ll be narrower versions on each side of the divider. (Check to be sure they won’t be so narrow that they’re impractical.) The key is to install a 3/4-in. plywood, particleboard or MDF panel between the center divider and the cabinet back to support the carriers.
Cut the panel to fit loosely between the divider and the cabinet back and high enough to support the top rollout position. Center the panel on the backside and middle of the divider and screw it into place with 1-in. angle brackets (they’re completely out of sight). Use a carpenter’s square to position the panel perfectly centered and vertical on the cabinet back and anchor it there, again using angle brackets. Measure, build and install the rollouts as we’ve shown.
Building wastebasket rollouts
Photo 13: Mark the openings
Build an upside-down version of the carrier and rollouts for the wastebasket drawer (Figure B). Center and trace around the rim of the wastebasket(s). Use a compass to mark the opening 1/2 in. smaller.
Photo 14: Cut the openings
Drill 1/2-in. starting holes and cut the openings with a jigsaw.
Photo 15: Slide the carrier in
Mount the wastebasket carrier and drawer as shown in Photos 10 and 11.
Wastebasket rollouts are just upside-down versions of standard rollouts. That is, the carrier is mounted on the top rather than the bottom of the rollout and the slides are positioned at the bottom edge of the carrier sides. That lets the wastebasket lip clear the MDF. Follow Figure B for the details.
We built our wastebasket rollout inside an 18-in.-wide cabinet, so we were able to fit two plastic containers back to back. If you only have a 15-in. cabinet to work with, you may be limited to one container mounted sideways. Buy your containers ahead of time to fit your opening.
With some wastebasket rollouts, you may need to knock the MDF free from the carriers after mounting so the wastebasket lips will clear. That’s OK; it won’t affect operation.
It may not always work to center rollout assemblies in all openings with equal spacers on each side. That’s especially true with narrow single cabinets that only have one pair of hinges. In our case, we had to cheat the wastebasket assembly away from the hinge side an additional 1/2 in. so it would clear. Again, it’s best to test things before permanent mounting. But if you make a mistake, it’s a simple matter to unscrew the assembly, adjust the shims and remount everything.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Air compressor
- Air hose
- Brad nail gun
- Cordless drill
- Drill bit set
- Framing square
- Miter saw
- Nail set
- Safety glasses
- Scribing tool
- Self-centering drill bit
- Table saw
- Wood glue
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 1 x 4 clear pine
- 1-5/8-in. screws
- 1/2-in. Baltic birch plywood
- 1/4-in. birch plywood
- 1/4-in. MDF or other plywood
- Brad nails (or finish nails)
- Side-mounted 22-in. full extension drawer slides