Save on Pinterest

How to Soundproof a Home Office

Seal holes, upgrade doors, and add layers of insulation and acoustic board to block sound transmission.

how to soundproof a home officeFamily Handyman

It’s hard to work in a home office with constant noise all around you. This article shows you how to soundproof a home office and block the racket. Use some or all of these solutions to have a peaceful, quiet work area.

You might also like: TBD

How to Soundproof a Home Office

Top of door detail

Install weatherstripping along the top of the door to block noise that would seep through the opening.

Bottom of door detail

A door sweep keeps noise from coming in along the bottom of the door and it’s one of the easy ways to learn how to make a door soundproof.

Wall switch detail

Insulate and caulk around outlets, switches and ductwork.

The way to stop the common problem of a noisy home office (other than evicting all teenagers) is to block the avenues sound uses to get into the room. Sound transmission reduction is a complex subject, but keep it simple by considering this basic scenario: A massive wall, whether it’s concrete or built-up drywall, is a great sound absorber and blocker, but it becomes useless if there’s even a tiny hole in it. Check out these tips on how to organize a home office, too!

The lesson? Start small. First seal openings into your office, and then consider strategies for absorbing more of the sound as it passes through the wall, ceiling, floor and door materials.

Try these solutions in the order shown.

  1. Install a solid-core door with vinyl weatherstripping and a bottom sweep and threshold.
  2. Caulk around ductwork and electrical boxes where they penetrate the drywall.
  3. Glue a layer of acoustic board and then another layer of drywall over the existing interior walls. This is a bigger project. It requires extending or moving electrical boxes, adding jamb extensions to doors, and removing and reinstalling casings and baseboard.
  4. If the noise is coming from upstairs, nail 1×2 furring strips on the ceiling with 3/4-in. rigid insulation in between. Run the strips perpendicular to the joists. Screw resilient channel to the furring strips with 3/4-in. screws, then hang 5/8-in. drywall from the resilient channel with 1-1/4 in. drywall screws. Tape, sand and paint the ceiling. Electrical boxes and heating registers will need to be extended or moved downward. Another big job.
  5. Glue a layer of acoustic board and drywall inside a stud space that’s being used as an air return. This will reduce the amount of return airflow by about one-third. Consult with a heating contractor to ensure that this won’t compromise your heating system.
  6. Install rigid foam insulation board or fiberglass batts behind and around ductwork and electrical boxes. You have to tear open walls.
  7. Fill wall and ceiling cavities with fiberglass insulation batts. If you open a wall for any another reason, add this step.
  8. If the noise is coming from below, loose-lay acoustic board under the carpet. This requires pulling up the existing carpet and tack strip, installing new tack strip and restretching the carpet. If you’ve got other annoying noises around the house, here’s how to eliminate annoying noises.

How to Soundproof a Home Office: Required Tools

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

  • Caulk gun
  • Circular saw
  • Dust mask
  • Hammer
  • Screw gun
  • T-square
  • Tape measure
  • Utility knife
If you’re tearing open the wall to add insulation behind electrical boxes, you’ll need tools to retape the walls, apply joint compound and repaint. If you’re installing acoustic board under carpet, you’ll need carpet stretching tools.

This tool list is for every solution. If you’re only doing a few these, you won’t need every tool.

How to Soundproof a Home Office: Required Materials

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • 1 x 2 in. furring strips
  • 3/4 in. rigid insulation
  • 3/4-in. screws
  • 5/8-in. drywall
  • Acoustic board
  • Caulk
  • Construction glue
  • Door sweep
  • Foam insulation
  • Resilient channel
  • Solid-core door
  • Vinyl weatherstripping