27 Life-Changing Garage Organization Ideas
These tips will help you reduce the clutter and get your garage back in order.
Double-Duty Shelf Brackets
Label cabinet drawers with pieces of plastic laminate and a permanent marker. Hot-glue the labels so they’re easy to pull off to relabel another drawer.
Overhead Rag Roost
Muffin Tin Hardware Bin
Attach a muffin tin under a shelf with a single 1/4-in. x 1-1/2-in. flat head machine screw. The tin pivots out from beneath work surfaces to organize and serve up any little doodad you frequently use. And you store all that little stuff without using up a single square inch of workspace. For best results when installing your muffin bins:
- Use muffin tins made from heavier gauge metal.
- Drill and countersink a 1/4-in. hole in the shelf top, so the top of the screw is flush with the shelf.
- Place 1/4-in. fender washers above and below the rim of the muffin tin.
- Tighten two nuts against each other on the underside so the threads won’t loosen.
On-a-Roll Pegboard Doors
The trick is to insert 1/2-in. plywood spacers in the roller hardware as shown. You can use the floor bracket that comes with the slider hardware to maintain the same 2-in. clearance at the bottom of the cabinet. For door handles, simply drill a couple of 1-1/4-in. holes in the pegboard with a spade bit. Now pop in the pegs and hang up your tools.
Overhead Storage in the Garage
Painting Gear Hangout
Organize your paint brushes, scrapers, roller frames, rags and paint cans with this shelf made from two 1×8 boards screwed together and reinforced with metal shelf brackets. We built ours 38 in. long to fit three brackets of sliding spring grips that we mounted under the shelf for tool storage. Build and attach this shelf to a shop or basement wall, and you’ll enforce orderly storage on all your far-flung painting paraphernalia.
Recycle Peanut Butter Jars
Yard Tool Organizer
Portable Storage for Free
Easy-Mount Mini Bins
Stacked Recycling Tower
Five plastic containers, six 2x2s and screws, and one hour’s work are all it takes to put together this space-saving recycling storage rack. Our frame fits containers that have a top that measures 14-1/2 in. x 10 in. and are 15 in. tall. Our containers were made by Rubbermaid.
If you use different-size containers, adjust the distance between the uprights so the 2x2s will catch the lip of the container. Then adjust the spacing of the horizontal rungs for a snug fit when the container is angled as shown.
Start by cutting the 2x2s to length according to the illustration. Then mark the position of the rungs on the uprights. Drill two 5/32-in. holes through the uprights at each crosspiece position. Drill from the outside to the inside and angle the holes inward slightly to prevent the screws from breaking out the side of the rungs.
Drive 2-1/2-in. screws through the uprights into the rungs. Assemble the front and back frames. Then connect them with the side crosspieces. Want even more space in the garage? Check out these DIY garage storage tips.
PVC Storage Hangers
- One 3/8-in. x 24-in. x 7-1/8-in. plywood piece for the sides
- One 3/8-in. x 24-in. x 4-3/4-in. plywood piece for the floor
- Two 1/2-in. x 4-1/2-in. x 4-in. plywood pieces for the ends
- Five 1/8-in. x 4-1/2-in. x 4-3/8-in. hardboard partitions
On a table saw, cut 3/16-in.-deep slots every 4 in. across the 24-in. x 7-1/8-in. piece of plywood. Make the slots just wide enough for the 1/8-in.-thick partition to slide in smoothly. Now saw the slotted piece into strips 4-1/2 in. and 2-1/2 in. wide. Use 1-in. brads and glue (predrilling for the brads) to assemble the sides and angled ends, then nail and glue on the floor. Drop the angled partitions into the slots, mount the rack to a wall, and go nuts sorting and organizing your scattered hardware. Here’s another seriously simple, space-saving storage solution for your workshop.
Adjustable Drawer Partitions
Apply weatherstripping to the sides of the drawers as shown, then cut the partitions long enough so they squish firmly into the rubber on both ends. A good rule of thumb is to make the partitions 1/4 in. longer than the inside measurement between the weatherstripping.
To install a partition, hold it at an angle to the front and back sides, then rotate it into position.
Bungee Cord Organizer
DIY Storage Wall
For just a few hundred dollars you can re-create this storage system yourself in one weekend. This project covers about 16 ft. of wall space and offers a multitude of ways to organize your garage.
Corner-on Pegboard Hooks
Ever had a plane, level or square get dinged up after falling off the pegboard? Never again. Bend an 8-in.-long pegboard holder into a corner shape by holding it in a vise and pounding it with a hammer to make the series of right angles. Make one corner to hold the left side of the tool and another to hold the right. Now just hold the tool up to the pegboard and insert the corner peg so it clasps the tool’s corner.
Purchase a large spring clip (about $3) from an office supply store and screw it to the wall. Clip notepads or gloves to the clamp and they’ll always be hanging around when needed.
Hijacked Tackle Box
Pie Plate Storage Pockets
Screw cut-in-half pie tins and heavy-duty paper plates to a shop wall and you’ve got space-saving storage for the sanding discs, circular saw blades and abrasive discs that like to hide in a drawer. Be sure to tape the sharp edges on the cut pie plates to protect your fingers!