Choose a connector that fits the wires
Wire nut connectors
Wire nut connectors come in many sizes.
Check the label on the wire nuts packaging
Check the list on the wire nut connector packaging to make sure your combination of wires is safe.
Every wire nut connector is made to join a certain minimum and maximum volume of wires: The larger the wire gauge, the fewer it can hold. Always check the approved list on the wire nuts packaging (photo above) to make sure the connector is listed for the wire combination you want to join. This is important for preventing home fires. Even though the connectors appear to be color coded, you can’t rely on this. For example, one style of yellow connector joins up to four 14-gauge wires, while another connects a maximum of three. You have to check the label on the package or go to the manufacturer’s Web site to find out. Keep a range of small to large wire nut connectors and their packaging on hand so you won’t be tempted to make do with the wrong size.
Line up the wire ends, then tighten
Photo 1: Install the wire connector
Place the wire nut connector over all of the wires.
Photo 2: Twist on the connector
Tug on each wire to make sure they are secure.
With the exception of stranded wire, which we’ll talk about below, it’s important to make sure the ends of all wires are lined up before twisting on the wire nut connector. Otherwise the connector won’t clamp all wires evenly and one or more could slip out.
Start by stripping the ends of the wires. Check the label on the connector package for the length of bare wire to expose. For all but the smallest and largest connectors, this is usually about 1/2 to 5/8 in. Then arrange the wires parallel to each other with their ends aligned. Keep your eye on the wire ends until the connector covers them to make sure none slips out of position. You don’t have to twist the wires together before you screw on the connector. Simply twist the connector until the insulated wires outside the connector begin to twist. Photos 1 and 2 below show how to install the connector. When you’re done, tug on each wire to make sure they’re all firmly connected.
Buy a wire-stripping tool
Wire stripping tool
Wire-stripping tools do a fast, clean job without nicking and weakening the wires. For most standard house wiring requiring 12-gauge and 14-gauge plastic sheathed cable, I like the Klein No. 1412 stripper ($18) shown here. It can cut the plastic sheathing of 12-2 and 14- 2 plastic sheathed cable, as well as strip insulation on individual wires.
Extend stranded wire 1/8 in. beyond solid wire
Extend stranded wire by 1/8 in.
If you hold the ends of solid and stranded wire even with each other while you screw on the wire nut connector, the stranded wire will often wrap loosely around the solid wires, resulting in a loose connection. This is especially likely when you’re joining multiple solid wires to one stranded wire. The problem is easy to prevent by extending the ends of all stranded wires about 1/8 in. beyond the solid wires. Then install the wire nut connector as usual.
Stranded wire is a little larger than the same gauge of solid wire. Use a wire stripper labeled for stranded wire, or use the hole for the next largest gauge of solid wire. Remember to tug on each wire to make sure the connector has a solid grip.
Loop the wire for a strong screw connection
Photo 1: Bend wire for a screw connection
Photo 2: Close loop around the screw
Since switches and outlets vibrate a little when used, it’s critical that the connections to them be strong so they don’t work loose. For screw connections, start with a 3/4-in. length of bare stripped wire. Photos 1 and 2 show how to bend the loop and close it around the screw. Wrap the wire clockwise around the screw so that the loop closes as the screw is tightened. Make sure to tighten the screw firmly. Keep in mind that only one wire is allowed under each screw.
Cut off nicked, bent or twisted ends
Use a stripper tool to expose clean, bare wire
Wires that are bent, twisted or nicked are weaker and won’t nest together as easily in the connector. Before you reconnect wires to an outlet or switch, or rejoin several wires with a connector, cut off the old bare wire ends and strip the insulation to expose clean, straight wire. It takes a few extra seconds but ensures a better connection.
If cutting a wire leaves it too short to work with easily, splice on an additional 6-in. length with a wire connector
Buy top-quality outlets for the best connections
Photo 1: Premium vs. economy outlets
Look for premium outlets with clamp screw terminals.
Photo 2: Stripping gauge
At most home centers, you can buy an economy outlet for about 50¢ or you can spend about $1.75 for a better one. That’s a big jump in cost for something that looks similar and does the same job. It’s tempting to buy the cheap one. But you get what you pay for. Premium outlets are stronger, make better contact with plugs and work more smoothly. Cheap outlets can literally wear out if you use them frequently. If you decide to buy premium outlets, look for the kind with clamp screw terminals (Photo 1). They resemble the ‘stab-in’ holes you’ll find on economy outlets but actually clamp down firmly when you tighten the screw. If you don’t want to spend the extra money to install premium outlets everywhere, at least put them in heavy-use areas like kitchens, garages, workshops and laundry rooms. Some of these areas may require GFCI protection. Always check with your local electrical inspector before replacing outlets.
Strip the wires to the length shown on the stripping gauge (Photo 2). Loosen the terminal screw by turning it counterclockwise to open the clamp. Then hold the wire or wires, one in each hole, while you tighten the screw. Tug on the wires when you’re done to make sure they’re securely connected.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Wire stripper/cutter