Step 1: Check for wires
Photo 1: For large hole drywall repairs draw a rectangle around the break with a straightedge or square to begin how to patch a hole in drywall. Look or put your hand through the break to feel for wires or other obstructions. Then cut out the section with a drywall saw or utility knife.Photo: Courtesy of The Family Handyman
Step 2: Insert backer boards
Photo 2: Insert 1×4 backer boards at each end of the hole and drive a pair of 1-1/4-in. drywall screws through the drywall into the boards to anchor them. Fit and screw a drywall patch to the boards.Photo: Courtesy of The Family Handyman
Step 3: Tape the joints
Photo 3: Lay a 1/8-in.-thick bed of patch drywall compound over the joints and press paper tape into the compound with a flexible 6-in. knife. Immediately apply a thin layer of compound on top of the tape. Allow to dry.Photo: Courtesy of The Family Handyman
Step 4: Apply a second and third coat
Photo 4: Apply a second coat of compound, drawing it at least 6 in. beyond the edge of the first coat to taper the edges of the repair. Let dry, then add a third coat to smooth any remaining uneven areas.Photo: Courtesy of The Family Handyman
Step 5: Sand the dry compound
Photo 5: Sand the dry compound lightly with 100-grit sandpaper to remove ridges and blend edges. Prime and paint.Photo: Courtesy of The Family Handyman
Before cutting out the damaged area of this how to fix drywall project, check the wall for obstructions. Often you’ll find a wire, pipe or duct (Photo 1). If so, work carefully around them with a drywall or keyhole saw. Or make a shallow cut by repeatedly scoring the line with a sharp utility knife. It’s easier to add backer board than to try to cut the drywall over studs (Photo 2) as you learn how to fix drywall. Cut the backer boards about 4 in. longer than the height of the hole. Pine or other soft wood works well. Hold them tight to the backside of the drywall when fastening them. Hold the boards carefully so the screw points won’t prick your fingers if they pop out the backside. The drywall screws will draw the boards in tight. Sink the screwheads slightly below the drywall surface.
Measure the thickness of the drywall (most likely 1/2 in.), and look for a large enough scrap from a damaged piece at a home center as you see how to fix a hole in drywall, rather than buy a full 4 x 8-ft. sheet. Cut it to size and screw it into place, spacing the screws every 6 in. Taping the edges of the patch drywall to make it invisible is the trickiest part of the how to fix drywall job (Photos 3 and 4). Buy a gallon tub of drywall compound and a roll of paper tape. You can use mesh tape, but it isn’t as strong. If you have a lot of repairs, also buy a sack of 20-minute setting compound. It hardens quickly and doesn’t shrink, so it’s ideal for filling cracks and gaps before applying the joint tape. For smoothest results, also pick up flexible 6- and 10-in. taping knives.
Apply a coat of compound and tape to each joint (Photo 3). Thin the compound a bit with water to help embed the tape. Smooth the tape with the 6-in. knife, pulling out from the center toward each end. Squeeze some, but not all, of the compound out from under the tape so you don’t create a big hump on the wall. Immediately apply a light coating to the topside of the tape, tapering it out onto the wall.
The second and third coats are to blend and smooth the taped joints so they’ll be invisible when painted. After each coat is dry, set a straightedge against the wall to check for obvious dips and bumps. Knock off bumps and ridges with your taping knife. Add more coats as needed. Then sand, prime and paint.
When possible, leave a few inches of drywall at corners so you won’t have to spread taping compound onto adjacent walls or ceilings and repaint them as well! Try to avoid common drywall installation mistakes.
Step 1: Drive a popped nail below the surface
Photo 1: Drive a popped nail below the surface of the drywall with a hammer and a nail set. Cut away loose joint compound and paper shreds.Photo: Courtesy of The Family Handyman
Step 2: Drive in drywall screws
Photo 2: Drive drywall screws about 1-1/2 in. above and below the popped nail. Sink the screwhead just below the surface of the drywall.Photo: Courtesy of The Family Handyman
Step 3: Fill the holes
Photo 3: Fill the holes with joint compound, swiping first across the holes, then down. Let dry, apply a second coat, then sand, prime and paint.Photo: Courtesy of The Family Handyman
Small holes caused by screws or hooks, wall fasteners or drywall fasteners that pop up are simple to repair, but again time consuming because you almost always have to repaint the walls. Nail pops are common and particularly irritating, because you’re likely to have more than one. But drywall screws sometimes pop up too, as a result of damp framing that dries out and shrinks during the first year or two in new construction.
The first step of the fix is to drive nails back down using a nail set (Photo 1). If you have screws, dig the drywall compound from their heads with a utility knife and turn them in tight with a screwdriver.
Then dimple the hole slightly concave with a hammer to indent any raised edges. But take care not to crush the drywall core. In addition, cut away any paper tears with a sharp utility knife. This is a good technique to use with old wall fasteners as well. It’s usually easier to tap them into the wall slightly rather than pull them out.
Two coats of drywall compound, applied with two swipes of the knife in a “+” pattern, should fill the holes (Photo 3). The first coat will shrink a bit, leaving a slightly smaller dent to be filled by the second coat. Scrape the excess off the surrounding wall so you don’t build up a hump. Sand lightly to blend with the surrounding wall. Be sure to prime the spot. Otherwise the topcoat will absorb into the patch and make the area look different from the surrounding paint. And use a roller when priming to help raise the surface texture to match the surrounding wall.
20-Minute Setting Compound
Twenty-minute setting compound is a great product for filling deep holes and gaps and for your first taping coat because, unlike regular joint compound, it hardens quickly without shrinking. That means less time spent filling. And you can apply a second coat of compound as soon as the first hardens. You don’t have to wait for it to dry completely as you complete a how to fix drywall project.
For most uses, buy the lightweight type. It comes as a powder in sacks. Mix only what you can use in about 10 minutes. It hardens quickly, often in your pan if you’re too slow! Completely clean your pan and knife before mixing a new batch in your how to fix drywall task. Otherwise it’ll harden even faster! To avoid clogging the sink drain, throw leftover compound into the trash.
Cracked corners sheetrock repair
Step 1: Cut through the tape
Photo 1: Cut through the tape at the ends of the cracked area and slice, scrape and tear away all loose tape and compound.Photo: Courtesy of The Family Handyman
Step 2: Apply joint compound
Photo 2: Apply a 1/8-in. layer of joint compound, then fold and press paper tape into it. Stroke the length of the tape, squeezing compound out on both sides. Let dry.Photo: Courtesy of The Family Handyman
Step 3: Apply second and third coats
Photo 3: Apply second and third coats to smooth the joint, tapering the compound about 6 in. out. Let one side dry before applying compound to the other side.Photo: Courtesy of The Family Handyman
Step 4: Lightly sand the repaired area
Photo 4: Lightly sand the finished repair using a fine-grit sanding sponge to make a crisp corner. Prime and paint to match the existing wall.Photo: Courtesy of The Family Handyman
Every home settles unevenly as it ages. This sometimes causes inside corners to crack or ripple. Often the crack will run from floor to ceiling. Once you spot this problem, watch it for two to three months for continued movement and fix it after all movement stops.
The key to renewing the strength of the corner is to remove all loose tape and drywall compound (Photo 1). If the drywall below has crumbled, cut it away with your utility knife and fill the gap with setting compound.
Retape the joint following the techniques shown in Step 1 of this how to fix drywall article. Crease the paper tape down the middle so it fits into the corner easily (Photo 2). It’s difficult to spread compound smoothly on one side of the corner without marring the other side. The trick is to apply compound for the second and third coats only on one side at a time. Let the one side dry, then do the other side.
Finally, buy a fine-grit sanding sponge to smooth the corners (Photo 4). It’ll do a nice job without gouging.
Required Tools for this Project
Have the necessary tools for this how to fix drywall DIY project lined up before you start—you’ll save time and frustration.
- Drywall sander
- Drywall saw
- Dust mask
- Screw gun
- Taping knife
- Utility knife
Required Materials for this How to Fix Drywall Project
Avoid last-minute shopping trips by having all your materials ready ahead of time to complete this how to fix drywall project. Here’s a list.
- Drywall screws
- Drywall tape
- Joint compound