Repair 1: Weather seal your garage door bottom seal
Photo 1: Remove the old garage door seal
Lift the garage door to about 6 ft. high and pull the old garage door bottom seal out through the gap behind the door track.Photo: Courtesy of The Family Handyman
Photo 2: Clean the track
Scrape dirt and corrosion out of the garage door bottom seal track with a screwdriver and a stiff brush.Photo: Courtesy of The Family Handyman
Photo 3: Install the new seal
Lubricate the rubber with a few drops of dish soap, then push and pull the new garage door bottom seal into the track.Photo: Courtesy of The Family Handyman
Photo 4: Fasten a new garage door bottom seal to a wood garage door
Push the track into wet caulk and tight against the door bottom. Clamp it into place. Then drill and screw the track to the back of the door using 1-in. screws.Photo: Courtesy of The Family Handyman
Photo 5: Apply weather stripping between door sections
Cut the weather stripping into strips the width of the door. Then fold along the crease so the “V” faces the outside. Insert the strip between the door sections, remove the adhesive backing and press it into place.Photo: Courtesy of The Family Handyman
Photo 6: Glue down a new threshold
Squirt out a bead of threshold adhesive according to label directions. Then move the threshold into place and align it with the chalk line you made earlier. Close the garage door bottom seal and let the weight hold it in position until the adhesive sets up.Photo: Courtesy of The Family Handyman
Photo 7: Nail on self-sealing door stop
Slide the door stop against the garage door so the vinyl seal bends at about a 45-degree angle. Then nail the stop into place with galvanized (or aluminum) 1-1/2-in. nails.Photo: Courtesy of The Family Handyman
If you want to keep the heat in your garage this winter or retain the cooled air next summer, you’ll have to do more than just install an insulated door. Most of the conditioned air escapes around and through all the cracks. Here are four simple ways to seal your garage door as much as possible. You can do the whole job in an afternoon for as little as $100, depending on the size of the door.
Measure the garage door for the seal
Start by measuring the width, height and thickness of your garage door. You’ll need those measurements to buy garage door stop with a built-in sealing lip and a new garage door bottom seal. While you’re at the home center, buy V-strip weather stripping, a tube of exterior caulk and a small can of wood sealer (if you have a wooden door). And for extra sealing power, buy a rubber threshold (one choice is the Storm Shield Garage Door Threshold; about $53 for 10 ft. 6 in. at garagedoorpartsusa.com).
Some garage doors come with a metal track that holds a replaceable rubber seal. Over time, the seal flattens and cracks. If that’s what you have, replace it with a “cold weather” silicone-type seal, which remains flexible in cold weather and lasts longer. If your home center doesn’t stock them, you can find one online; see one source above. Lubricate the silicone seal with dishwashing detergent and slide it into the track slots.
Remove the old garage door bottom seal
Lift the door just enough that the garage door track doesn’t get in the way of the weather seal, then slide out the old rubber bulb (Photo 1). You may need to pry the track ends open with a flat screwdriver if they’ve been crimped. If it’s especially stubborn, cut it and remove it in pieces.
Clean the door bottom (Photo 2), then cut the new rubber seal to length with a razor knife. Thread the T-shaped edges into the weather seal track, then slide the seal across the door. Be patient—it takes a lot of pushing and pulling even with a helper.
If you have a wooden garage door, rip off the nailed rubber seal. Then seal the wood with wood sealer. While the sealer dries, prepare the new aluminum track by cutting it to length and notching the ends so it fits around the bottom roller. Next, lay down a thick bead of caulk along the leading edge of the door and attach the track setup (Photo 4).
Prepare the areas between the door sections by cleaning them with a rag and household cleaner (be careful not to pinch any fingers). Then install the pressure-sensitive V-strip weather stripping (Photo 5). Repeat for each section.
Install the threshold
Now move on to the threshold. Start by cleaning the concrete with degreaser and water. Rinse and let dry. Then roll the threshold into place with the hump on the inside of the garage door and cut to the width of the opening. Gently close the door onto the threshold and square up the hump to meet the door seal. Mark the edge of the threshold on the floor at each end and snap a chalk line along your marks. Next, glue the threshold into place. Close the door firmly against the threshold and leave it closed until the adhesive dries (Photo 6).
Install the stop
Pry off the old door stop and install new door stop that has a sealing lip (Photo 7).
Seal a garage door gap, Part 2
Here’s how to deal with gaps caused by an uneven bottom door panel or sunken concrete.
The easiest, but least elegant, method is to install several pieces of bottom seal retainer and rubber gasket in the gap areas. Just measure the thickness of your bottom panel and buy sections of seal retainer and gasket from a garage parts supplier (garagedoorpartsusa.com is one online source). Mount the retainer to the bottom panel wherever there’s a gap. Finish the job by sealing the top edge of the retainer with caulk and then paint to match the door. This fix works on wood and metal doors.
If you have a wood door and want a cleaner look, remove the existing bottom seal and scribe/cut the bottom panel to match the contour of the concrete floor. Seal the freshly cut wood with wood sealer. Then remount the bottom seal.
Repair 2: Replace rotting garage door trim
Photo 1: Remove the old garage door trim
Cut through any caulk lines with a utility knife, then pry off the old garage doorstop, brick mold and jamb.Photo: Courtesy of The Family Handyman
Photo 2: Install the new jamb
Use a clamp to hold up one end of the top jamb, then nail the jamb to the framing with 8d galvanized casing nails.Photo: Courtesy of The Family Handyman
Photo 3: Glue and nail brick mold
Spread PVC cement on both sides of the mitered corners, then hold them together until they bond.Photo: Courtesy of The Family Handyman
Photo 4: Add stop molding
Mark the width of the trim piece at several points on the jamb, then nail. Trim the overlapping rubber seal at the corners.Photo: Courtesy of The Family Handyman
Wood garage doorjambs and trim often rot near the bottom or get crunched by bumpers.
A good, long-lasting solution is to replace the wood jamb, brick mold trim and doorstop with paintable solid vinyl pieces that won’t crack or decay. Available at home centers and lumberyards, the three pieces cost a total of about $4 per ft.—comparable to clear wood. The vinyl can be cut, nailed and painted just like wood. It’s available in white, but you can order brown, bronze and tan. Fill nail holes with white caulk or exterior wood filler, then if desired prime and paint with acrylic latex. Use a light paint color over white vinyl to keep it from overheating.
Remove the old jamb and trim (Photo 1), then nail the vinyl jamb to the frame, beginning with the top piece (Photo 2). Fasten every 12 to 16 in. with 8d galvanized nails or stainless steel trim screws. Precut the miters on the top piece of brick mold trim and nail it to the framing every 12 in. with 10d galvanized casing nails. Use 6d casing nails for the stop molding, nailing it at the premarked points on the trim.
If the temperature is below 40 degrees F during installation, predrill nail holes and leave a 1/8-in. gap at the ends of the jamb for expansion.
Glue the brick mold corners with PVC cement (Photo 3), then nail them into place after the glue sets. To avoid breaking the joint, wait at least an hour for the glue to fully cure before nailing within a foot of the corner. Splice long runs with glued butt joints.
The edge of the vinyl stop molding should be 2-1/2 in. back from the garage door so the rubber seal fits loosely against the door (Photo 4).
Repair 3: Clean up a rusty door track
Photo 1: Trim the rusty end
Mark the bottom of the track, then cut the metal with a reciprocating saw or hacksaw.Photo: Courtesy of The Family Handyman
Photo 2: Clean and paint
Clean the bottom of the track with mineral spirits, wire-brush the rust, and then paint the area.Photo: Courtesy of The Family Handyman
Garage door tracks often rest directly on damp concrete floors, where they eventually rust. However, there’s no reason they can’t be slightly above the floor and stay dry: The garage rafters carry the weight of the track and the angle brackets hold the track in place.
Clean up the tracks and prevent rusting by simply cutting off the bottom 1/2 in. First make sure all the angle bracket bolts are tight, then cut the track bottoms off (Photo 1). Use a rag dipped in thinner to remove any lubricant on the first 6 in. of track, then scrape and brush off as much rust as you can. Finally, paint the bottom with a metal spray paint that’s formulated to bond to rusted areas (Photo 2). Rust-Oleum Rust Reformer is one choice.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Drill/driver - cordless
- Miter saw
- One-handed bar clamps
- Pry bar
- Reciprocating saw
- Safety glasses
- Tape measure
- Utility knife
- Wire brush
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 8d and 10d
- Dish soap
- Door bottom gasket
- Galvanized casing nails; 6d
- Metal spray paint
- PVC cement
- Solid vinyl trim
- Threshold gasket
- Weather seal