Save on Pinterest

The Expert Guide for Exterior Home Repairs

Don't be intimidated by exterior issues with your home. You can do all of these maintenance and repair projects yourself—we'll show you how.

1 / 41
how to replace a damaged shingleFamily Handyman

Replace a Damaged Shingle

Asphalt shingles withstand years of abuse from wind, rain,  sleet and snow, but they can tear like cardboard when struck by a falling tree limb or branch. Replacing the shingle will only take about 10 minutes— just be careful not to damage any other shingles.

2 / 41
replace vent flashingFamily Handyman

Replace Vent Flashing

All-metal plumbing vents present two opportunities for leaks—first, where the flashing meets the roof, and second, where the vent pipe meets the flashing. When the latter situation occurs, caulking and similar fixes will prove to be only temporary cures. You’ll have to replace the flashing, either with a rubber-sleeve version or the telescoping two-piece type. Here’s how to replace vent flashing.

3 / 41
fix a patchy lawnFamily Handyman

Fix a Patchy Lawn

Achieving a lush lawn doesn’t have to be a constant struggle. And you don’t have to pay big bucks for a lawn service to douse your yard with chemicals, either. Growing healthy, green grass is mainly just a matter of knowing what to give your lawn, and when to give it. Follow this advice from a pro to get your lawn shipshape before summer.

4 / 41
How to Glaze a WindowFamily Handyman

Fix Windows

Obviously, you can’t glue broken glass back together. But, for windows that get stuck, let in drafts or have moisture issues, there are DIY solutions. Fix old windows, double-hung windowswindow glass glazing and screens. You can also stop window drafts and learn how to avoid and remove window condensation.If you want to take on a larger task, you can even replace your windows!

5 / 41
seal a valley jointFamily Handyman

Seal a Valley Joint

Occasionally, a flashing that’s still intact can allow water passage; this is especially true for valley flashing that doesn’t have a raised fin or ridge in the center to help prevent fast-moving water from sloshing. If the roofer didn’t cement the joint—and many don’t—the shingles can curl up at the edge and eventually create a gap that water can easily penetrate.

Starting at the bottom edge, lift the shingle and apply a heavy, consistent bead of roofing cement along the flashing. Press the shingles down to seat them.

6 / 41
Weather-strippingFamily Handyman

Weatherstripping is Easy

If you can see light creeping beneath exterior doors, air is also escaping. Grab a few packages of self-adhesive rubber foam weatherstripping and go to town, sealing any and all doors that lead outside. Weatherstripping already installed but you’re still suffering from a high gas bill? It might be time to replace the strips installed by the previous owners. Check out this handy tutorial on installing weatherstripping.

7 / 41
reattach a gutter end capFamily Handyman

Reattach a Rain Gutter End Cap

For a long-lasting repair of those annoying gutter leaks, turn to silicone sealants. Silicone will act as an adhesive to keep the end cap securely in place, as well as a sealant to stop leaks and drips. Attach the end caps using caulking and riveting techniques. Well-stocked home centers and hardware stores will have everything you need. Check out these easy gutter fixes.

8 / 41
Easier gutter cleaning with a spatulaFamily Handyman

Easier Gutter Cleaning

An old plastic spatula makes a great tool for cleaning debris from gutters! It doesn’t scratch up the gutter, and you can cut it to fit gutter contours with snips. Grime wipes right off the spatula too, making cleanup a breeze.

9 / 41
repair leaky metal gutter seamsFamily Handyman

Repair Leaky Metal Gutter Seams

For water to make it to the downspouts and drain properly, it has to stay in the gutter channel. When couplings or other fittings leak, the water drips right next to the foundation. A simple repair can stop the leak.

In most cases, you can apply a new bead of gutter sealant between the adjoining surfaces and use new pop rivets that are the same size as the old ones. Check the diameter and depth range to make sure they’ll fit the old holes and will cinch the joint tight.

10 / 41
Patch a leaky gutterFamily Handyman

Patch a Leaky Gutter

Left unrepaired, leaks from your gutters can result in water damage to the house siding and eaves, as well as create drainage problems that affect the foundation or basement. Patch small leaks before they grow.

Remove any accumulated debris use a wire brush to clean off surface rust. Spread plastic roofing cement directly over the leaky seam or hole and at least 6 in. beyond in both directions. Next, embed a piece of repair mesh or a piece of prebent metal flashing in the roofing cement and press firmly to seat it. Then recoat with a second layer of cement and apply a coat of aluminum paint

11 / 41
fertilizeFamily Handyman

Feed the Lawn

If your yard is mostly grass with just a few weeds, forgo the expensive landscaper. With one trip to your local hardware store or plant nursery, you can purchase $25-$50 worth of supplies, spend just a few hours on your lawn, and simply wait for the grass to grow. Check out this easy guide on fertilizers and seed spreaders.

12 / 41
how to get rid of weeds in lawn - man spraying weed killerFamily Handyman

Eliminate Weeds From Your Grass

Eliminate weeds in your lawn and prevent their return by maintaining healthy grass, using a minimum of weed killers and good timing. We show you six strategies that simplify weed control and reduce your weed patrol chore. Tips to eliminate weeds from your backyard grass.

13 / 41
thinning lawnFamily Handyman

How to Revive a Thinning Lawn

Revitalize your lawn a weekend using just one or two tools. An aerator helps the soil breathe and a power rake gets it ready for seeding. Tips to reviving grass in a thinning lawn.

Learn about lawn aerator options and which one is best for your yard here.

14 / 41
straighten guttersFamily Handyman

Straighten Gutters and Add a Splash Gaurd

If your metal gutters have developed a middle-age sag, it’s time for a little tummy tuck! You’ll find some version of a gutter support bracket that’ll work on your gutters to lift the low spots. It’ll help drain water better and help keep debris from accumulating. If your metal gutters have developed a middle-age bulge, get ’em back in shape with these easy-to-install gutter hangers.

15 / 41
fix for overflowing guttersFamily Handyman

Quick Fix for Overflowing Valley Gutters

If rainwater cascading down your roof valley causes a waterfall that washes out the petunias every time it storms, install a splash guard. It takes about 20 minutes to complete. Attach the guards with 1/2-in. sheet metal screws

16 / 41
holes in sidingFamily Handyman

Fix Holes in Siding

Nail holes in aluminum and vinyl siding are tough to repair without replacing the entire piece, but a squirt of color-matched caulk from a siding supplier will solve the problem for a lot less money and aggravation.

17 / 41
replace broken deck boardsFamily Handyman

Replace Broken Deck Boards

You don’t have to let a split, rotted or otherwise ugly deck board ruin the appearance of your deck. Simply replace it and in a year or so the replacement will blend right in. Here’s how to replace a broken deck board.

18 / 41
deck crack cleaner HHFamily Handyman

Crack Cleaner

Cleaning the expansion joints in a sidewalk or the spaces between deck boards doesn’t have to be a tedious, on-your-knees job. Insert a “screw-in” hook into the end of a broom and drag the hook through the cracks. The hook will pull out debris, which can then be easily swept up.

19 / 41
stiffen a bouncy deckFamily Handyman

Stiffen a Bouncy Deck

A deck that bounces when you walk across it won’t feel strong and solid, even if it meets structural requirements. The cause is usually long joist spans between beams or between a beam and the house. To stiffen a deck, you have to be able to get to the framing underneath.

20 / 41
fix sway in deckFamily Handyman

Take Out the Sway with an Angle Brace

Some otherwise solid decks tend to sway or wobble as you walk across them, especially decks resting on tall posts 4 or more feet above the ground. Angle-bracing the posts is one good solution to this problem, but the braces often look tacky. Instead, install an angle brace underneath your deck. It’s a virtually invisible fix that all but eliminates sway.

21 / 41
replace popped deck nailsFamily Handyman

Replace Loose, Popped Deck Nails

Decking swells and shrinks as it goes through repeated cycles of wet and dry seasons. This frequently causes nails to loosen and pop up above the deck boards. You can drive them down again, but chances are that’s only a short-term solution. They’ll probably pop up again after a few years. The long-term solution is to remove the popped nails and replace them with deck screws.

Tap the claw of a cat’s paw under the nail head and lever the nail up. Finish pulling with a hammer or pry bar. Protect the deck board with a shim or thin block.

22 / 41
screw over stubborn nailFamily Handyman

Solution for Stubborn Nails

If the head breaks off a stubborn nail and you can’t get it with a pry bar, try pulling it with locking pliers. Grip the nail tip and roll the pliers over to get it going. If the nail shank breaks off, don’t worry. Just drill a pilot hole beside the nail and drive in a screw. The screw-head will cover the nail.

23 / 41
roof under deck

Roof Under a Deck

This low-cost, easy-to-build system catches the water that drips through the deck boards and redirects it to the outside of the deck. Now you can use the area under the deck as a covered patio and can enjoy warm summer rainstorms without getting wet. Here’s our step-by-step project guide.

24 / 41
power wash deck powerwashFamily Handyman

Clean and Refinish Your Deck

The basics of refinishing a deck are pretty straightforward: Strip, clean, stain … repeat! It’s a tough chore that might take you several days to complete, one you’ll have to do every few years to keep your deck looking great. Here are some things to think about before tackling the job yourself.

25 / 41
deck restoration coatingFamily Handyman

Deck Restoration Coatings

Deck restoration coatings are acrylic based and go on like really thick paint. You’ll need to apply two coats. Once dry, they form a coating similar in appearance to composite decking. Here’s how to apply this deck restoration coating.

A word of caution: Read the manufacturer’s instructions before use and contact the company directly if you have questions or concerns about whether it’ll work for your particular situation.

26 / 41
patio deck tilesFamily Handyman

Deck Tiles

Think of this option as a slipcover for your deck. Instead of ripping out or recoating your old deck boards, you place new wood or synthetic decking right over your old deck. Several companies make tiles out of composite or exotic woods like ipe that you just lay down and snap together. Plastic grids underneath the tiles allow for airflow, which helps prevent wood rot. Here’s everything you need to know about deck tiles.

27 / 41
air-conditioning-service-clean-condenser-coilsFamily Handyman

Air Filter

It is instinctual for homeowners to contact an HVAC tech when they notice irregularities in their cooling or heating system. These irregularities could be a direct result of a dirty or clogged air filter. We encourage homeowners to check their filters and replace if necessary. It’s also beneficial for homeowners with pets, carpet, or for homes near fields or construction zones to have multiple filters for convenient replacement.

Pro Tip: Mark your calendars! 1-in. filters should be changed every month, 2-in. filters should be changed every 2 months and 4 to 5-in. filters should be changed every 6 to 12 months.

28 / 41

Remove a Tree Stump Painlessly

We’ll show you how to remove a tree stump without breaking your back. This method is safe and effective, and doesn’t require a lot of manual labor. But you have to be patient. The process can take several weeks.

29 / 41
replace sidingFamily Handyman

Replace and Repair Wood Siding

Has some of your siding begun to rot while the rest is still good? Don’t replace all the boards. Follow these easy steps and just replace the boards that are rotted.

30 / 41
replace exterior doorFamily Handyman

Replace an Exterior Door

Replace a worn, drafty front door with a stylish new energy-efficient one. Replacement doors come pre-hung in a weatherstripped frame and you don’t have to be a master carpenter to do a first-class job. We’ll show you the techniques that will result in a perfect, weathertight installation.

31 / 41
Wash fence powerwasherFamily Handyman

Power-Wash a Grimy Fence

Power washers are aggressive. They’ll strip the wood as well as clean off the dirt and grime, but you can also erode the wood too deeply and ruin it. The key is to use the right sprayer tip and technique. In any case, the power washer’s spray will slightly raise and roughen the grain on smooth wood. That’s actually good—it allows more sealer to soak in and improves the finish. Here’s how to make a gray, sagging wood fence look new again.

32 / 41
Glue damaged wood fence piecesFamily Handyman

Make Simple Repairs to Your Fence

With the fence clean, it’s time to fix or replace damaged boards, refasten loose boards and countersink any protruding nails. Use waterproof glue to repair any split and broken boards. Drive corrosion-resistant screws instead of nails to pull loose pieces tightly together. If a gate is sagging, straighten it with a turnbuckle support.  Also, coat the posts where they emerge from the ground or concrete with a wood preservative. This is the area that rots first.

33 / 41
touch up a vinyl-clad fenceFamily Handyman

Touch Up a Vinyl-Clad Fence

Vinyl-clad chain-link fence keeps its appearance for a long time. But the vinyl can get scuffed and worn where the gate latch locks onto the post. The repair is a little tricky because you’re trying to paint over vinyl and metal. If you use a spray paint formulated for metal, it won’t bond well to the vinyl. Instead, coat the damaged area with paint formulated for plastic. Here’s how to do it.

34 / 41
repair pitted asphaltFamily Handyman

Repair Pitted Asphalt

Are tufts of grass sprouting from your asphalt driveway? Well, if you don’t do something about the pot holes and cracks in the pavement, they’re not going to go away. In fact, they’ll only get worse, especially if you live in a cold climate where ice and freeze/thaw cycles reign. Fix the little problems now and you’ll add years to the life of your driveway. Over time, every asphalt driveway develops cracks and pits. Here’s how to fight back.

Tramp the asphalt into the hole with a 4×4 post. If the tamped area is lower than the driveway surface, add more asphalt patch until it’s about 1/2 in. above the driveway surface and tamp again. Do this until the filled area is flush with the surface.

35 / 41
repair cracked asphaltFamily Handyman

Repair Cracked Asphalt

Pour in crack filler until it’s flush or slightly below the driveway surface. If the filler settles, add more. Follow the manufacturer’s instructions for drying time before applying the sealer. Remove any vegetation growing in the cracks before filling them. Here’s how to do it. 

36 / 41
caulk cracked concreteFamily Handyman

Caulk Cracked Concrete

Cracks and gaps in concrete are more than just an eyesore. Water can get into the joints, freeze and then expand, making the cracks even larger. Gaps against a house can direct water against the foundation, leading to more problems. Once a year, go around your home and fill these gaps and joints with urethane caulk to prevent problems. Seal cracks in concrete with durable urethane caulk. You can do it in less than a half hour.

37 / 41
fixing concrete step cornerFamily Handyman

Fix a Chipped Step

Assemble an L-shaped wooden form, lock it into place with bricks and fill the void with concrete repair mix. A repair mix will stick to the old concrete better than standard concrete mix. If you don’t want to buy a special edging tool to round the edges of the patch, carefully shape the edges with a putty knife.

Also, learn how to make your patio pavers perfectly smooth again.

38 / 41
prime wood before you caulkFamily Handyman

Prime Before You Caulk

When it comes to wood (or wood-based materials like hardboard), primer sticks better than caulk and provides a great adhesion surface for caulk. So if caulking is part of an exterior painting project, it’s best to prime before you caulk. Work the primer into gaps, but don’t try to fill them with primer. Here’s how to make exterior caulks last longer.

39 / 41
perfect bead of concreteFamily Handyman

Get a Perfect Bead on Concrete

On horizontal concrete, you can skip the tooling mess and get a perfect bead by using a self-leveling polyurethane sealant. Just insert backer rod and inject the syrupy sealant. Resist the urge to tool the caulk; it will slowly level out and form a neat seal. Be sure the backer rod completely seals the crack. If the caulk seeps past the rod, you’ll get an ugly sinkhole and a weaker seal, and you’ll waste expensive caulk (this specialty caulk will cost you about $8 for a 10-oz. tube).

40 / 41
seal a drivewayFamily Handyman

Seal a Driveway

An asphalt driveway can last almost 30 years. But you can’t achieve that long life span unless the driveway was installed properly and you perform regular maintenance, like annually filling cracks and applying sealer when needed. Here you’ll learn how to clean and prepare the driveway so you get the longest life and best protection from driveway sealer.

41 / 41
best finish for outdoor woodFamily Handyman

The Best Finish for Outdoor Wood

A spar finish is almost exactly like the interior polyurethane finishes we’re all familiar with. It forms a shiny coating that protects the wood while accentuating the color and grain. The application is the same as with interior polyurethane too. The big difference between spar and interior poly is that spar stands up to exterior conditions. It’s more elastic, so it’s less likely to crack as wood shrinks and swells from moisture changes. It also protects wood from UV sunlight damage. Originally developed for boats, spar finishes are now used mostly for outdoor furniture and entry doors.

Make your exterior paint job last longer with these pro tips.