Overview: Materials, tools and costs
Paneling a ceiling is a great way to add character to a plain room. And if the existing ceiling is cracked or water-stained and in need of a makeover, all the better. Covering it with panels and beams is more elegant and less expensive than hiring a pro to restore a damaged ceiling to its original condition.
A paneled ceiling like this normally calls for expensive tools and lots of carpentry skill, but we designed this project to be DIY-friendly. It’s made easy by a homemade circular saw ripping jig, the installation of a simple 2×4 framework and miter-free joinery (Figure A). The visible finished material over the framework is MDF. It’s inexpensive, readily available at home centers, and smooth and easy to work with. However, cutting, sanding and routing MDF is extremely dusty, so do all your power tool work outside or at least in the garage with the overhead door open, and be sure to wear a dust mask.
While the ease of construction is a big plus, the real beauty of this project is its low cost. The materials for this 12 x 12-ft. ceiling cost less than $350, including the paint.
Three Shortcuts Make This Project DIY-Friendly
1. Miter-free joints: There is no such thing as a miter on this project. Every end joint is a straightforward square cut. Just get the length right, cut at 90 degrees on your miter saw, and all the joints will look like a million bucks.
2. Chamfered edges: Small 45-degree chamfers routed on the edges of all the exposed trim hide all but the worst imperfections.
3. Overhangs: The vertical side trim overhangs the ceiling panels to hide any sloppy cuts. And the caps overhang the side trim, so small gaps there will be hidden as well.
Step 1: Choose the design for your room
Our system is ideal for dressing up any ceiling whether it’s damaged or perfect, textured or flat, drywall or plaster. If your ceiling is flat and in good shape, you can omit the MDF panels and simply paint the ceiling and apply the grid work and trim right over the existing material. But keep in mind that you’ll have to make the side trim strips 1/2 in. wider to account for the missing panel thicknesses.
The nine-panel pattern works for rooms up to 13 ft. wide and 33 ft. long. The use of materials is efficient and the shape of the panel will automatically be proportional to the shape of the room. A square room will have square panels; a rectangular room will have rectangular panels.
Figure A: Ceiling Cross Section
In a nutshell, the MDF trim fastens to a 2×4 grid that’s screwed to the ceiling.
If you love the natural look, you can panel your ceiling with any type of wood and still use the techniques we show. Use painted MDF for the panels and solid natural wood for the beams, or go all out and use matching veneered plywood for the panels. To save money when you use this technique, rip plywood for the side trim pieces. That’ll look fine since the plywood edges will be hidden. You can also use any type of wallpaper or covering on the panels, or on the existing ceiling drywall if it’s in good shape.
Step 2: Lay out and install the 2×4 grid
Photo 1: Mark the grid on the ceiling
Mark out the beam pattern with chalk lines. Then make it easy on yourself by marking the joists with a different color chalk.
Photo 2: Install 2x4s
Screw 2x4s to the ceiling perpendicular to the joist direction with a couple of 3-in. screws into each joist.
Photo 3: Add crossing 2x4s
Screw the overlapping 2x4s to the first ones at each intersection. Fill the spaces between the lower 2x4s to complete the grid work. Space screws every 16 in.
The first step in laying out the grid work is to chalk lines around the perimeter of the room 4-1/2 in. away from the walls. That will allow the full 5-1/2-in. cap to fit against the wall and match the rest of the finished trim. Then measure the length and width of the space inside. It’s up to you how many panels to use and how big to make them. Most average-size rooms work well with nine panels. In other words, divide both room dimensions by three. You’ll only be able to have perfect square panels if the room is square. Otherwise, you’ll have rectangles, which is fine—they’ll look great as long as they’re a consistent size. And you can always make the panels exactly the same size. Make them as large or as small as you wish, as long as they’re under 4 ft. wide and 8 ft. long, as much as the sheets will allow.
Once you figure out the panel sizes, snap the grid layout on the ceiling (Photo 1). To avoid some confusing math (accounting for the width of the 2×4 grid), just snap center lines to lay out the grid and then snap lines 1-3/4 in. on both sides to mark the outsides of the 2x4s. It’s a good idea to snap lines marking all the ceiling joists at this point so you’ll know where to put the fasteners for the grid and ceiling panels.
Step 3: Cut and install the panels
Photo 4: Install the panels
Cut the panels to size, prime them and then nail them through the drywall into the joists.
Cut the panels 1/2 in. shorter than the grid openings to make them easy to slip into place. Cut them to width first and set aside the 8-ft.-long waste pieces to use for trim caps and hubs. Then cut them to length. You can just snap chalk lines and cut the panels “freehand” since the side trim pieces will hide imperfections. Then roll on a stain-blocking primer (KILZ and BIN are two brands) with a 3/8-in.-nap roller sleeve. If you’re working alone, make yourself a support crutch (Photo 4) to hold the panels tight against the ceiling while you nail them into each floor joist with 2-1/2-in. nails spaced every 8 in.
Fill the nail holes with wood filler. Sand down any excess filler and surface imperfections and spot-prime those areas. Then roll on two coats of latex paint.
Step 4: Assemble a jig and cut the side trim and cap trim
Photo 5: Cut the trim
Rip the top cap trim using a ripping jig. The simple three-part jig gives you straight cuts and perfect widths.
MDF panels are heavy—90 lbs. for a 3/4-in. sheet! So even if you have a table saw, you’re better off cutting side trim and caps with a ripping jig (Photos 5 and 9) and a circular saw. Here’s how to make a jig that will accurately cut the trim pieces you need for the ceiling:
- Rip an 8-ft.-long, 3-in.-wide “fence” for a top cap ripping jig (Figure B).
- Rip one 2-1/2-in.-wide “stop” out of 1/2-in. material for ripping the trim strips for the side trim (Figure C) and a 3/4-in.-thick stop for ripping the caps and hubs. Rip the stop and fence from the edges of new sheets, and always face the factory edges toward the saw for straight, true guide surfaces.
- Screw each stop to the jig base with countersunk 1-1/4-in. screws spaced every 12 in., and then screw the fence to each stop wherever it needs to be to match the width you’re ripping.
The key to both jig setups is the distance from the left side of your circular saw’s base to the edge of the saw blade (Figure B). That distance will determine fence placement.
You’ll have to set up the ripping jig twice with two different fence locations and the stop that matches the thickness of the material you’re cutting (1/2-in.-thick side trim or 3/4-in.-thick caps and hubs). The base of the jig is the same for both jig setups—a 1/2-in. or 3/4-in. sheet of any flat sheet good. Or use one of the MDF sheets and make panels with it later.
Hubs are cut from the 5-1/2-in. cap strips, so while you still have the jig set up, make sure you rip enough stock for those, too.
Figure B: Top Cap and Hub Jig
Assemble the jigs from MDF or plywood.
Figure C: Side Trim Jig
Assemble the jig from MDF or plywood.
Step 5: Rout, prime and install the trim
Photo 6: Install the side trim
Nail the side trim to the framing. Paint and mask the panels with painter’s tape first to avoid fuss when you paint the trim.
Photo 7: Rout the hub edges
Cut the hubs to length, then rout the edges using a “corral” tacked to your workbench to safely hold the small pieces in place.
Photo 8: Install the hubs
Center and nail the hubs at each intersection. Don’t forget to prime the freshly routed edges.
Photo 9: Rout and install the caps
Use the top cap ripping jig to hold the caps in place while you rout the edges. Cut them to length and nail them to the grid with 2-in. brads.
Photo 10: Finish the beams
Patch the nail holes, lightly sand, spot-prime and then paint the grid-work trim.
Photo 11: Pull the tape
After you paint the trim, slice through the tape at the inside corners and peel it away.
Figure out roughly how long the caps will be and cut and rout the hubs from the extra material. Sand off any saw blade marks on the edges of the cap stock and rout those edges (Photos 7 and 9). Prime the pieces. Cut the side trim pieces to length and nail them to the grid sides. Then nail on the hubs. Cut each top cap to length. Chamfer the ends and nail each into place.
Improve Your Lighting
Since you’re covering the drywall with panels, this is a great time to add or move ceiling light fixtures. If you have a floor above, just cut channels in the drywall and drill holes through the middle of joists, or staple the cables on the sides of joists to get the cables to the new electrical boxes or recessed light canisters. If you have an attic above, you’ll have to crawl up there to run the cables. Just remember that when you mount the new boxes, they should be flush with the finished MDF surface. You’ll need to add 1/2-in.-deep plaster rings to existing boxes before you install the finished ceiling.
DIY Success Story
When Brian Dohrwardt added a small second-floor bathroom, he ran into a big problem. The undersized floor joists didn’t allow a path for the drain lines (drilling 4-in. holes through 7-in. joists is a recipe for floor collapse!). His only option was a bad one: He had to run the pipes under the floor joists and along the ceiling of the dining room below. But those ugly, exposed pipes inspired a beautiful solution. Brian built false, hollow beams to enclose the pipes. The resulting coffered ceiling is the best feature of his home, Brian tells us.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Chalk line
- Chamfer router bit
- Circular saw
- Countersink drill bit
- Drill bit set
- Drill/driver - cordless
- Dust mask
- Finish nail gun
- Framing square
- Hearing protection
- Miter saw
- Paint roller
- Roller tray
- Safety glasses
- Sanding block
- Stud finder
- Tape measure
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- MDF, 1/2 in. and 3/4 in.