How to Reduce Sump Pump Noise

It's easy to forget about your sump pump, but it's important to make sure it's in good working order. If you don't, you could end up like the homeowner who returned from a weekend trip to discover his entire basement floor covered in 1/2 in. of water. After shutting down the power, he waded over to the sump pump and noticed it wasn't working. Upon closer inspection, he realized that the cable attached to the float must have gotten tangled somehow. It took him two seconds to untangle the cable, and then he spent the next 15 hours dragging out waterlogged carpet, running the wet/dry vac and moving fans around. To avoid a similar disaster, be sure your pump has a vertical float switch. Also, check your pump at least a couple times a year by dumping water into the basin to make sure everything is working properly.

A technician was assisting a water softener installer who was replacing a fairly new softener because the first one had ruptured and filled the pipes with little zeolite beads. The installer didn't seem too worried about why the first one failed, but the assistant did a little investigating. A water pressure test gave a reading of more than 110 lbs. psi. The culprit was the 20-year-old pressure-reducing valve. After a new valve was installed, the pressure went down to about 75 lbs. Pressure-reducing valves are usually found near the main water shutoff valve, but not all homes have them. It depends on your municipality. High water pressure can harm pipes, connections, and appliances. It also creates water hammer and waste massive amounts of water. Checking for high water pressure is an often overlooked maintenance item, and one that's easy enough to perform. A new pressure-reducing valve and a simple pressure gauge like this one that hooks up to a spigot or laundry tub faucet are both available at home centers. Plus: Appliance Care and Maintenance Tips to Make Appliances Last

Many sliding windows and vinyl replacement windows have weep holes on the exterior bottom of the frame. These holes are designed to drain away rainwater that can collect in the frame's bottom channel. Weep holes can get plugged with bugs and debris, and if that happens, water could fill up the channel and spill over into your house. To see if your weep system is working, simply pour a glass of water into the track or spray the outside of the window with a garden hose. If you don't see a steady stream of clean water exiting the weep hole, poke a wire hanger into the hole, or spray it out with compressed air, and wet it down again. If the little flapper (designed to keep out driving wind) is stuck shut, it can be removed with a putty knife and replaced.

If you've never had a problem with water in a window well, you may never think to clean it out. Here's what happened to one homeowner who neglected his window wells. After an average rainfall, not even a heavy downpour, a clogged gutter dumped a lot of water next to his house and into his window well. The leaves in the well acted like a pool liner, preventing drainage, and the water level rose higher and higher until the pressure broke the basement windows. Gallons and gallons of water poured into the basement, ruining everything in sight. Unfortunately, he had no insurance coverage for that type of flood. Don't let this happen to you. Keep window wells clean with a cover, available at home centers.

A distraught homeowner called a plumber because her water heater wasn't heating, and furthermore, it was leaking. Right away, the plumber asked if the homeowner had been draining some of the water from it every year. The puzzled homeowner said, 'No. Why?' It turns out that sediment will collect at the bottom of the tank. This creates hot spots on gas-powered heaters that can damage the tank and cause premature failure. On an electric water heater, sediment buildup can cause the lower heating element to fail. So, occasionally draining a water heater will lower energy bills and extend its life. We recommend draining water heaters at least once a year. Plus: 12 DIY Ways to Make Your Stuff Last Way Longer

A plugged dryer vent will cause your dryer to run inefficiently, and that's bad. A plugged dryer vent could also cause a house fire, and that could be deadly! Dryers that are centrally located in houses are most prone to plugging because of the longer ducts. Excess lint is only one reason ducts get clogged; nesting pests and stuck exhaust hood flappers can also cause backups. Stronger odors and longer dry times are two signs your vent is plugged. You'll have to remove the vent from the back of the dryer to clean it. Suck debris from the ducts with a wet/dry vac, or ream them out with a cleaning kit that includes a brush on a long flexible rod that attaches to a power drill. The kits are available at home centers. If your ducts need replacing, get smooth metal ducts, which will stay cleaner longer than the rough corrugated surface of flexible ducts. Avoid plastic ducting altogether; it can be a fire hazard. Plus: Slash Heating Bills

A properly balanced door is less likely to injure someone or something and keeps the door opener from working too hard, which will shorten its life. To check the balance on a door, close the door and then disengage the opener by pulling the opener release handle. Manually pull up the door about halfway and let go. A properly balanced door will stay in the halfway position by itself. If it falls, the tension needs to be increased. If the door rises, the door spring has too much tension, which means it's working harder than it needs to. Check the door a couple times a year. Adjusting the spring tension is tricky and dangerous. Call a garage door professional to perform the service, or see advanced garage door repairs. Plus: Reclaim Your Garage-Organize It!