Super-stable plywood base
The plywood widens the base making the saw more stable. Plus you can quickly screw the plywood down to sawhorses, benchtops or other places you set the saw.
A “must do” with any new portable table saw (when you're not using a leg set) is to attach a 3/4-in. plywood base with a hole cut in the center. This simple base allows you to clamp or screw the table saw to sawhorses, which provide a wide foundation for added stability. This also raises the saw off the ground to a comfortable working height. The hole in the bottom lets the sawdust fall through and helps keep the saw running cool. But that's not all the base has to offer. Drill a couple of 1/2-in. holes on one side so you can hang the saw from hooks fastened to the workshop or garage wall when you're finished using it.
Cut the plywood base a few inches wider and longer than the base of your saw, and then cut a 1-sq.-ft. hole in the center. Center your saw on the plywood and mark the mounting holes. Drill a 1/8-in. hole through the plywood at each mark. Flip the piece over and drill 1-in. dia. holes about 1/4 in. deep to recess the carriage bolt heads. Next, drill 5/16-in. holes in the center of the recesses. Pound in the carriage bolts, slip the saw over the bolts (use spacers if they come with the saw) and fasten the saw to the base with washers and nuts.
Every table saw user has horror stories about near misses and not-so-near misses. No doubt about it: Table saws can be dangerous. Always approach them with respect. Use your blade guard whenever possible and always wear safety glasses and hearing protection. Read your owner's manual and make sure your saw is properly adjusted.
Cut-off block for duplicate lengths
Clamped block allows you to make repetitive crosscuts without risking a kickback. Caution: We removed the blade guard for this photo; use yours!
Dangerous kickback can occur when you crosscut directly against a rip fence. Kickback happens when the part of the board between the fence and the blade gets pinched, and the blade, spinning toward you, catches it and hurls it back at you.
You can prevent this hazard with a simple block. Cut and clamp a block to the side of your rip fence and then position the fence the correct distance from the blade (the length of cut plus the thickness of the safety block). Clamp the block so that as the workpiece enters the blade it's no longer in contact with the safety block. This crosscutting method prevents the workpiece from binding between the fence and the spinning blade. Never make a cut that binds against the blade in any way. Think through all your cut setups before you start!
Dado guide using standard blade
Step 1: First cut
Make your first cut by aligning the top dado mark with Line No. 1 drawn on the miter gauge fence. This cut establishes one edge of the dado. The line takes into account the thickness of your blade. Caution: Blade guard must be removed for this procedure.
Step 2: Second cut
Make your second cut by aligning the same dado mark with Line No. 2 on the fence as shown. This cut establishes the other edge of the dado. To finish the dado, just make several passes to cut away the area between your initial cuts. Make slight adjustments if the fit is too tight or too loose.
The board should fit snuggly into the dado.
Cut accurate dadoes without a dado blade by making successive passes over the blade. The tough part here is to get a tight fit (Photo 3). Screw a 1×3 fence extension to your miter gauge and make a saw kerf in it. For a tight fit, trace the thickness of the board onto the homemade miter gauge fence extension (see Photo 1). Then follow the Photos 1 and 2. Try this method on a test piece to get the hang of it.
A simple outfeed jig
A simple outfeed jig supports those long, dangly boards.
Cut long boards confidently with an easy-to-make outfeed jig screwed to your plywood base. Be sure to have the highest point of the jig even with the saw table. The gradual incline of the jig (about 12 degrees) helps guide sagging pieces and slowly bring them up as you push your board through the saw. Ordinary rollerstyle outfeed supports don't work well for long boards because they have a tendency to tip over when the board sags and hits the stand beneath the roller. This jig works especially well for long, thin pieces such as siding, which tends to sag and separate as you cut.
Figure A: Outfeed jig
Build this simple outfeed jig from ordinary 3/4-in. plywood and 2×4 scraps. Be sure to screw the jig to the plywood base of the saw for stability (your saw base must be screwed or clamped to the sawhorses as well). You won't need anything other than a single 2×4 for the far leg support.
Note: Figure A can be downloaded and printed from Additional Information below.
Video: How to Cut a Rabbet Joint with a Table Saw
Fast, flawless plywood edging
Add a floating fence
If you’ve ever covered plywood edges with solid wood, you know how hard it is to position the edging flush with the plywood surface. Next time, try this: Start with edging that’s about 1/8 in. wider than the thickness of the plywood. That way, you can attach the edging fast, without worrying about a flush fit. To trim off the excess edging, clamp or screw a tall “floating fence” to your table saw fence. Then position the floating fence so it’s flush with the outer edge of the blade.
Rip clean edges
Finding the perfect position requires a couple of test runs. But when you get it right, you’ll be able to trim the edging in seconds. And if you use a good-quality smooth-cutting blade, you can remove the saw marks with only light sanding.
Cut skinny strips safely
Custom rip guide
Cutting thin strips can be dangerous. There’s no space between the blade and the fence for a push stick, and on some table saws you have to remove the blade guard. Five minutes and a 6-in.-wide scrap of plywood or particleboard are all you need to cut safely and quickly. Just screw a wooden “heel” to the scrap and you’ve got a sliding guide that lets you leave the guard in place and keeps your fingers safe. Add a handle to make it easier to pull the guide backward after each cut.
Straighten a crooked board
To cut a straight edge on any board, all you have to do is mount the crooked board to a larger carriage board and run the whole assembly across your table saw. You can fasten the crooked board with screws or—if you don’t want to put screw holes in the board—hold it firmly in place with 4-in.-long screwed-down cleats at both ends. Set your saw’s fence to match the width of the carriage board. That way, you can tell exactly where the blade will cut the crooked board.
Cut rabbets with a dado blade
Precision rabbet guide
A dado blade in a table saw is the fastest way to cut notches, or “rabbets,” along the edge of a board. And here’s a way to make the process even faster: Set the blade to cut slightly wider than the rabbet width. Then clamp or screw an auxiliary fence to the saw’s fence. Now—instead of fussing with dado adjustments—you can precisely adjust the width of the rabbet by moving the fence and allowing the dado blade to cut into the auxiliary fence.
Admit it: You sometimes use your table saw as an auxiliary workbench, slopping it up or damaging it. Better to build a plywood cover to protect it from glue, paint and tools. Cleats at the edges prevent the cover from sliding off the saw. Makes a great coffee table too!
Avoid laminate disaster
Fence for cutting laminate
An auxiliary fence mounted tightly against the table is essential when cutting plastic laminate (or any other thin material) on a table saw. Without it, skinny stuff can slip under the fence and cause a crooked cut, major chipping, kickback and injury, and ruin an expensive sheet of laminate.
Instant stand and outfeed
Safer rip cuts
With a few minutes, a couple of 2x4s, a slab of plywood and a pair of sawhorses, you can build a stand for a benchtop saw, plus a long outfeed table.
Align the outfeed
On the version shown here, the 2x4s are notched so that the saw table is flush with the plywood. Screw the plywood to the 2x4s and the 2x4s to the horses. Also screw or clamp the saw to the 2x4s.
Upright cuts—for lap joints, tenons or rabbets—aren’t a good job for a table saw. That is, unless you build a simple box to guide and support the workpiece. Precise cuts depend on a precise box, so take the time to build it square and sturdy. And as always, make your adjustments and mistakes using scraps before cutting precious wood.
Check the miter gauge before cutting
Think of the markings on your miter gauge as approximate, not exact. For real accuracy, drop by a woodworking store or an art supply store. For a few bucks, you can get a setup tool that’s as accurate as the most expensive square. Use it to set your miter gauge to 45 or 90 degrees. This works with your miter saw and other tools too.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.