Make a Perfect Miter Joint

Take your woodworking up a notch with these great tips.

Next Project

Introduction

In pursuit of the perfect miter joint? These tips for tighter miters cover common situations you'll undoubtedly encounter in your workshop.

Tools Required

  • Biscuit joiner
  • Corner clamps
  • Miter saw
  • One-handed bar clamps
  • Router
  • Table saw
  • Utility knife

Materials Required

  • Accelerator for cyanoacrylate glue
  • Biscuits
  • Cyanoacrylate glue
  • Masking tape
  • Slow-setting wood glue
  • Sticky notes
  • Wood glue

Project step-by-step (13)

Step 1

Use scrap wood guides for a perfect fit

Lock your piece into position

Family Handyman

It’s dang near impossible to get the length and position of a mitered part right unless you can butt it up against the adjoining miters. To provide a guide, tape or clamp mitered scraps in place. Remove the scraps as soon as you glue the part in place—otherwise, stray glue might make those temporary guides permanent.

14 Pro-Approved Tips for Tight Miters

Step 2

Match wood grain

Make miter joints less visible

Family Handyman

Whether you’re banding a tabletop or making a picture frame, make sure the wood color and the grain pattern match at the miters. Selecting matching wood at the lumberyard takes only a few extra seconds and gives you much better-looking miters.

Amazing Miter Joint Clamp

Step 3

Align with biscuits

Lock corners together perfectly

Family Handyman

It’s not easy to align and clamp miters, especially when they’re lubricated with a coat of slippery glue. That’s why woodworkers often use biscuits on miter joints even where extra strength isn’t needed. Cutting biscuit slots is a minor job that provides major help at glue-up time.

How to Cope Joints for Wood Corner Trim

Step 4

Square up with corner clamps

Get 90 degree corners every time

Family Handyman

With some miter-clamping methods, you need to grab a square and make sure the corner is exactly 90 degrees. Not so with corner clamps; they automatically hold parts perfectly square. They’re available at home centers or online.

How to Make Perfect Cuts With Circular and Miter Saws

Step 5

Miter, assemble, then rout

Create sharp, perfectly aligned corners

Family Handyman

Shaped moldings can be tough to miter, align and clamp. So make life easier by starting with plain square stock. Then, after assembly, grab your router and shape the edges. The risk with this method is that you’ll gouge or splinter parts that are already in place. The best way to avoid disaster is to make a series of shallow passes instead of one full-depth cut.

Perfect Trim on Doors, Windows and Base Moldings

Step 6

Slow down your glue

Give yourself extra time

Family Handyman

It’s hard enough to align and clamp miters without rushing to get it done before the glue begins to set (in five to 10 minutes, and even faster in warm, dry conditions). That’s why there are slow-setting wood glues, which give you an extra 10 minutes or so. If you can’t find a slow version at your favorite home center, make your own. If you add one part water to 20 parts wood glue, you’ll gain about five minutes of working time. The water will also weaken the bond very slightly. So if strength is critical, order slow-setting glue online. Titebond Extend is one common brand.

Rehearse Before You Glue

A dry run—complete assembly with clamps but without glue—is the best way to ensure a smooth, successful glue-up, whether you’re assembling miters or anything else.

No Cutting Corners: Tips for Tight Miters and Coped Joints

Step 7

Clamp with your hands

Easier assembly for hard-to-clamp parts

Family Handyman

When you’re dealing with small or other hard-to-clamp parts, your hands make the best clamps. Simply rub the glued surfaces together and hold them tightly on a flat surface for about a minute. Let go and allow the joint to set for 30 minutes before handling it.

Tips for Tight Miters and Miter Cuts

Step 8

Micro-adjust with paper shims

Fine-tune miter cuts

Family Handyman

If you’ve ever tried to adjust the angle of your miter saw by one-tenth of a degree, you already know how hard micro-adjustments are. Here’s an easier way: Slap a few sticky notes on the fence, make test cuts and add or remove sheets until you get exactly the angle you want.

How to Cope Baseboard Trim with a Miter Saw

Step 9

Feel the difference

Use your sense of touch

Family Handyman

When you’re building a box or frame, the opposite sides have to be exactly the same length. To make sure they are, do the touch test: Set the parts side by side and run your finger over the mitered ends. You may not be able to see a slight length difference, but you’ll feel it.

Step 10

Close ugly gaps

Pro trick

Family Handyman

You can close a small miter gap by rubbing it with a screwdriver shank or any hard, smooth tool. We used the end of a utility knife. That crushes the wood fibers inward to make the gap disappear. Even professional woodworkers sometimes resort to this crude trick.

Finish Carpentry Tips

Step 11

Make your own corner clamps

Put extra pressure on miter joints

Family Handyman

This is an old favorite among woodworkers: Clamp on notched blocks, then add a bar clamp or two to squeeze the joint. This allows you to put a lot of pressure on the joint without buying any special clamps. If you’re assembling a four-sided project such as a picture frame, join two corners first. Then, after the glue has set, join the two halves of the frame.

Step 12

“Lengthen” a board

Snatch victory from the jaws of defeat

Family Handyman

Ever cut that last part just a bit too short? There’s a solution for that: First, trim off the inside edge of the too-short part. By cutting off the short edge, you effectively make the mitered part longer. Then trim the same amount off the outer edges of the other three sides. Your edging will be a little thinner than you had planned, but nobody will notice.

Home-Made Miter Clamps

Step 13

Bond joints instantly

Get better results when you glue small pieces

Family Handyman
Trim carpenters have used this system for years: Apply a few dabs of cyanoacrylate adhesive (aka “superglue”) to one surface and apply activator (or “accelerator”) to the other. Immediately press the parts together and they’ll bond in seconds. No waiting, no complicated clamping setup. Activator is sometimes sold separately ($5 and up), sometimes with the glue. Look for it at home centers or shop online; rockler.com carries a good selection of glues and activators.