• Share:
Shortcuts for Custom Built Cabinets

Built-in bookcases, shelving and cabinets are faster, easier and better with these tips from a veteran cabinetmaker. Ken Geisen has been building high-end custom cabinets, shelving and entertainment centers for 20 years. Here are some of his best tips for cutting labor and hassles—without sacrificing quality.

By the DIY experts of The Family Handyman Magazine

Shortcuts for Custom Built Cabinets

Built-in bookcases, shelving and cabinets are faster, easier and better with these tips from a veteran cabinetmaker. Ken Geisen has been building high-end custom cabinets, shelving and entertainment centers for 20 years. Here are some of his best tips for cutting labor and hassles—without sacrificing quality.

Tip 1: Set cabinets on a platform

Most lower cabinets include a base or toe-kick that raises them off the floor. But Ken doesn't build them that way. Instead, he builds a plywood platform that acts as the base for an entire row of cabinets. The platform can be under- sized to allow for a toe space or full size for a more traditional look (as shown here).

This approach has a couple of major advantages. First, cabinet construction is simpler. The cabinets are just boxes; no extended sides to form a base, no toe-kick cutouts. Second, installation is faster. Leveling one platform is a lot easier than positioning each cabinet individually. Ken sets the box 1/4 in. from walls to allow for wavy or out-of-plumb walls.

Tip 2: Quick, classic side panels

When the side of a cabinet box will be exposed, you have to hide the cabinet back's edge somehow. The usual method is to rabbet the side and recess the back. But Ken gets a richer look with less hassle. He simply glues and nails the back to the cabinet box and hides the exposed plywood with a frame and panel for a classic look. And since the cover panel is a separate part, it's easy to scribe it to the wall before fastening it to the cabinet.

Tip 3: Secret screws for shelves

Lots of designs have upper shelf units that rest on lower cabinets. Here's Ken's trick for fastening the shelf units to the cabinet top so that the screws are hidden: He sets the cabinet top on the lower cabinets and scribes it and sands it to fit the wall. But he doesn't screw it in place yet. Instead, he positions the shelf units on the top and carefully slides the top forward just far enough so that he can drive screws into the shelf sides and dividers. After sliding the top back into place, he screws the top to the cabinets from below and screws the shelf units to the wall.

Tip 4: Back-bevel wall stiles

Before scribing stiles that will meet walls, bevel the back edge on your table saw. That way, you'll have less wood to belt-sand off when you shape the edge to the contour of the wall. Ken cuts a 45-degree bevel about 1/2 in. deep, so he has only 1/4 in. of wood remaining.

Tip 5: Break down face frames

Pocket screws are a standard joinery method, but Ken has a nonstandard approach. He assembles face frames with pocket screws, but without glue. He sands the frames, labels the back of each part and then disassembles them for easier finishing. Transport is easier too: Ken can pack a mile of face frame parts into his van and carry them into the house without banging up walls. The cabinet boxes need less TLC too, since they're frameless during transport. Once on-site, Ken reassembles the frames with pocket screws and glue. For pocket joinery, Ken uses a Kreg Jig.

Tip 6: Thicker backs save time

Most cabinetmakers use 1/4-in. plywood for cabinet backs. But Ken prefers 1/2-in. material. The thicker plywood usually adds only a few bucks to the cost of each box and eliminates the need for a hanging strip or “nailer” at the back of the cabinet. That means quicker construction and a cleaner interior look. Best of all, it allows you to drive a screw through the back anywhere, not just at the nailer.

Tip 7: Use prefinished plywood (sometimes)

With its tough, flawless clearcoat, prefinished ply- wood eliminates finishing hassles. But Ken uses it only for “no-show” parts like cabinet boxes and shelves. Finishing other parts to match the color and sheen of the factory-finished plywood is just too difficult. Finding prefinished ply- wood can be difficult. Your best bet is a lumberyard that caters to cabinetmakers.

Back to Top

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 4 of 4 comments
Show per page: 20   All

October 17, 10:35 AM [GMT -5]

I'll tell you what. Where I live, custom cabinets are EXPENSIVE. As they should be. A friend of mine installed a TV stand, with lower cabinets 8 feet wide. 4 floating shelves. a valance with 4 led lights inside. Painted white. It cost him $6800.00. The work is flawless by a well known local company.

I'll make my own.

March 24, 2:44 AM [GMT -5]

Great old school way to build true custom cabinets. Facilitates Plumb and level installation. Happy to see the custom install has not been lost in the big box shuffle.

November 15, 9:56 PM [GMT -5]

Great Ideas

September 18, 12:51 AM [GMT -5]

Also, I like to use a strip of pegboard as a jig for hole drilling for adjustable shelves.

+ Add Your Comment
closeX

Add Your Comment

Shortcuts for Custom Built Cabinets

Please add your comment
closeX

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today
closeX

Report Abuse

Subject
Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us

Featured Product

Buy Now