How to Build a Garden Bench

Make this attractive, comfortable garden bench. We show you how to build it with simple biscuit joinery.

Garden bench overview: Design, tools and materials

I built this bench four years ago. Since then, it’s been used and abused as a prop on photo shoots, and sat on and commented on by staff and passersby. The first thing they all notice is the design—simple but handsome. Then, as soon they sit down, they’re all surprised by how comfortable it is.

Finally, everyone admires my amazing woodworking skills. But the truth is, this bench is just plain easy to build. I used only biscuits and screws, the simplest types of joinery. Still, the bench is surprisingly strong. It’s been hauled around, knocked around and used as a mini scaffold—and once it even fell out of a moving pickup. But it’s still solid.

Round up the tools and materials
I spent about $95 for the lumber for this bench. You may have to buy more lumber to get knot-free pieces, so your cost may vary. You’ll find everything you need to build this bench at your local home center or lumberyard. Refer to the Materials List in Additional Information below, then choose the lumber carefully to avoid large knots.

In addition to the lumber, screws and wood plugs, you’ll need No. 20 wood biscuits and a special tool called a plate or biscuit joiner to cut the biscuit slots. You can buy a good-quality biscuit joiner for $100 to $170. You’ll also need some clamps, a table saw and a router fitted with a 1/4-in. round-over bit.

Figure A: Garden Bench Details

Overall Dimensions: 60" long, 16-1/2" wide, 16-3/4" tall

You can download and enlarge Figure A, including Part B and Part F Details, in “Additional Information” below. You can also download a complete Materials List and Cutting List in “Additional Information.”

Garden bench technical drawing showing all parts Figure A: Garden bench details
Back to Top

Step 1: Cut out and drill the parts

Start by inspecting your boards and planning the cuts to take advantage of the knot-free sections. Use a table saw to rip the boards to the right width. For crisp, clean edges, rip about 1/4 in. from the edge of the boards before you rip them to the final width. To work around knots, you may have to rough-cut some of the boards to approximate length before ripping them. When you’re done ripping, cut the parts to length. We used a 1/4-in. round-over bit and router to ease the edges of the seat boards. It’s a great task for a router table setup if you have one.

Next, measure and mark the center of all the screw holes and drill 3/8-in.-deep holes for the 1/2-in. wood plugs. I used a Forstner bit to create clean, flat-bottom holes.

Back to Top

Step 2: Cut the biscuit slots

The final step in preparing the parts for assembly is cutting the biscuit slots. If you’ve read my previous plate joiner story, you know I’m a proponent of a technique I call the bench reference method. Rather than use the adjustable fence to position the slots, you simply place your work-piece and the base of the biscuit joiner against the bench top and cut the slot. To find the story, type “biscuit joints” in the search box above.

The only downside to this method is that the slot isn’t always centered on the part, so you have to pay close attention to orientation as you cut the slots and assemble the bench. You’ll see how I use masking tape to keep track of the orientation. Photos 2 – 5 show the plate-joining techniques I used to cut slots in the parts.

Back to Top

Step 3: Assemble the garden bench with biscuits and screws

Photos 6 – 10 show the assembly steps. Biscuits connect the legs to the rails for extra strength. Spread exterior wood glue in the slots and on the biscuits. Then clamp the parts until the glue sets. Use 2-1/2-in. deck screws to attach the legs to the braces (Photos 7 and 9). If you aren’t using self-drilling screws, drill pilot holes to avoid splitting the parts. Attach the top slats to the frame with 1-5/8-in. deck screws.

Back to Top

Step 4: Finish the garden bench

I plugged the screw holes with 1/2-in. flat-top birch plugs, but if you own a drill press, you can make your own cedar plugs using a 1/2-in. plug cutter.

I finished the bench with Cabot Australian Timber Oil. This penetrating oil finish leaves the wood looking natural, but it has to be reapplied every year. For a glossy, more permanent finish, you could use Sikkens Cetol SRD or spar varnish.

Video: How to Make Wood Plugs

Jeff Gorton, an editor for The Family Handyman, will show you how to make wood plugs, for countersunk screws, match perfectly.

 

Back to Top