• Share:
How to Bend Wood

Curved hardwood nosing on a countertop can really make your project stand out. Here's how to make a 3/4-in. laminated hardwood nosing that bends perfectly around round countertop corners.

By the DIY experts of The Family Handyman Magazine

First, buy or make the strips

There are several ways to tackle this tough chore, but bending and laminating several thin strips to create 3/4-in. nosing will give you the best results. The first step is to buy or make thin stock (1/8 to 3/16 in.) for the nosing. For the counter shown in the photos below, we planed 1/4-in. x 2-in. red oak down to 1/8 in. thick. You can also create thin strips by ripping 2-in. thick stock on a table saw with a high-quality, smooth-cutting ripping blade. The strips should be at least 1/8 in. wider than the finished nosing to allow for sanding. They should also be long enough to leave tails that will run a few feet along the straight part of the countertop where you'll splice in the remaining nosing.

Be sure to select boards with fairly straight grain and no knots so they can bend without breaking. To make the boards even more pliable, we soaked them in hot water in a 10-ft. aluminum gutter. However, if the radius is large enough, you may be able to skip this step. Just make a few extra strips and do a dry test to find out.

Next, glue up the laminated trim

If you soak your boards, use polyurethane glue to laminate them together. Polyurethane glue, which needs moisture to work, gives a long working time and fills gaps well. Be sure to wear gloves; this stuff tends to make a mess.

Spread the glue, stack the strips together and attach them in one step. Using three-way edge clamps (available at home centers), begin clamping the stack of strips at the center of the half-circle. Leave all the clamps in place for at least 12 hours. Remember, you can't have too many clamps, especially for this job.

Finally, keep it wet while it dries

If you soak the strips, it's a good idea to wet the outer face frequently for the first three or four hours. This will help prevent the outer strip from cupping away from the face, since the outside dries first. An even better option is to clamp an unglued sacrificial strip on the outside so the layers can dry evenly.

Even though this wood-bending technique is time-consuming and challenging to master, it's so cool that once you've tried it, you'll probably find some excuses to try it again.

Tip: The polyurethane glue will begin to foam as it cures. You can easily scrape the foam off when it's dry.

Back to Top

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

    • Clamps
    • Miter saw
    • Air compressor
    • Air hose
    • Brad nail gun
    • Tape measure
    • 3-way edge clamps
    • Belt sander
    • Paint tray
    • Sawhorses
    • Paintbrush
    • Table saw

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.

    • Hardwood boards or strips
    • Polyurethane glue

Comments from DIY Community Members

No comments on the article have been posted yet. Be the first to add your comment!

You will be required to log in or create an account to post a comment.


Add Your Comment

How to Bend Wood

Please add your comment

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today

Report Abuse

Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us