• Share:

Tool-apron storage

Tool aprons can be modified to store nearly any household item. Just sew a variety of pocket widths in the aprons, then mount the aprons by screwing a wood strip through the top of each and into a door. For hollow-core doors, use hollow anchor fasteners to hold the screws firmly to the door.

Storage pockets for skinny things

Saw off short pieces of 1-1/2-, 2- or 3-in. PVC plumbing pipe with 45-degree angles on one end. Screw them to a board to hold paintbrushes, pencils, stir sticks and just about any other narrow paraphernalia in your garage. Mount them by drilling a 1/4-in. hole in the angled end, and then drive a 1-5/8-in. drywall screw through the hole into the board.

Double-duty shelf brackets

Shelf brackets designed to support clothes hanger rods aren’t just for closets. The rod-holding hook on these brackets comes in handy in the garage and workshop too. You can bend the hook to suit long tools or cords. Closet brackets cost about $3 each at home centers and hardware stores.

Cutlery tray tool chest

Be honest! Somewhere you have a tool drawer bursting with a combination of screwdrivers, nail sets, tape rolls, utility knives, scissors, scrapers, measuring tapes, files and knives. And often you have to dump everything out to find one tool. Here is a solution. Fit a large cutlery tray in the drawer to organize the tools so you can see and grab the one you want in a second. The tray is easy to lift out and carry to a job, and if you use a metal mesh tray, dust can’t build up between the tools.

Electrical box toolholders

Junction boxes can hold a lot more than switches and wiring. Nail or screw them wherever you need handy holders for small stuff. They come in different sizes and shapes and cost 50¢ to $2 each.

Cannery row hardware storage

Don't recycle those steel or aluminum cans quite yet. Set aside a few months’ worth of fruit and coffee cans and put these cannery rows to work organizing all of the small hardware in your shop. All you need are some homemade wood clips and a chunk of 3/4-in. plywood screwed to a wall. To make the clips, rip a 3/4-in.-thick board into 1-3/8-in.-wide strips. Saw or rout a 3/8-in. x 1/4-in. rabbet along one edge. Drill 1/8-in. screw holes every 3/4 in. and then cut off 3/4-in.-wide clips. To mount the clips and cans on the plywood, screw on a clip, notch end down, then set a can on the clip and screw on a second clip overlapping the can's rim about 1/4 in. That’s it! Keep adding clips and cans until every screw, bolt, nail and nut has a can to call home. Label the cans, and keep one loaded with surplus clips and screws for adding on.

Overhead garage storage

Stow bulky items overhead by cementing together a simple rack from 2-in. PVC pipes and fittings. Bolt the straight pipe to the ceiling joists to support heavy loads, and screw the angled pieces from the "wye" connectors into the cross brace to stabilize the whole rack. The PVC’s smooth surface makes for easy loading and unloading.

Screw storage

If you keep screws in a coffee can, you're probably used to the screw points pricking your fingers. The can also collects dust and dirt. Instead, buy a clear water bottle with a pop-up lid and pour the screws into the bottle with a funnel. The screws stay clean, and you can shake them out of the bottle one at a time.

Ladder pouch

There's no need to load up your tool belt when you're working from a ladder. Any type of hook, pouch or pocket made for a tool belt works just as well when mounted on a ladder.

Back to Top

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 5 of 5 comments
Show per page: 20   All

November 28, 4:01 PM [GMT -5]

A good variation of the "apron" which i use is an over the door Shoe organizer. it can be hung over a closet door, or even screwed into a wall.
it has about 6 rows of 4 pockets. and mine is even clear plastic making it easy to see what's inside.

November 05, 5:12 AM [GMT -5]

Please be very careful when making any modifications to a ladder, since it is a structurally engineered piece of equipment. Be especially careful when making any large holes or adding any significant weight to the major components of the ladder, such as the legs, steps or braces. Modifying the ladder CAN reduce its stated load rating, resulting in a collapse of the ladder and injury to its user.

January 10, 11:43 PM [GMT -5]

All of these were good.

September 14, 6:41 PM [GMT -5]

Lovin' these ideas....a great way to recycle and repurpose every day items

September 14, 12:04 PM [GMT -5]

Wonderful ideas! I can use every one!!

+ Add Your Comment
closeX

Add Your Comment

Savvy Home Tool Storage

Please add your comment
closeX

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today
closeX

Report Abuse

Subject
Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us