• Share:
Unclog a Bathtub Drain Without Chemicals

Fix a clogged tub drain quickly and easily by removing the stopper and fishing out the hair and gunk that causes the problem 80 percent of the time. We show you how to open most common types of drains.

By the DIY experts of The Family Handyman Magazine

Unclogging tub drains—the drop stopper type

About 80 percent of the time, you can fix slow-draining or clogged tub drains in five minutes, without chemicals and without a $100 plumber bill. In most cases, you'll only need a screwdriver and a stiff wire or a bent coat hanger. The problem is usually just a sticky wad of hair that collects on the crossbars, a few inches under the stopper. All you need to do is figure out how to remove the stopper (that's almost always easy) and fish out the gunk. Bend a little hook on the end of the stiff wire with a needle-nose pliers and shove it through the clog—you'll nearly always extract the entire ugly mess. If hair is wrapped around the crossbars, slice through it with a utility knife and then grab it with the wire.

Follow our series of photos to determine which type of stopper you have and how to remove it.

Photo 1: Lift the stopper and loosen the screw on the
shaft slightly. Slide the stopper off the shaft.

Photo 2: Hook clogged hair with a bent wire and
pull it out.

Clearing a Drop Stopper Drain

The most common type, a drop stopper, has a setscrew located under the cap.

Push/Lock drain stoppers

These stoppers lock and seal when you press them down and release when you push down a second time. The way to remove them isn't so obvious. In most cases you have to hold the stem while unscrewing the cap as shown. With the cap off, you can sometimes fish out the hair from the crossbars. Otherwise simply remove the entire shaft by unscrewing it. You may have to adjust the screw tension on the stem when you reinstall everything to get a good seal.

Unscrew the stopper top and unscrew the shaft if necessary.

Unscrew the stopper top and unscrew the shaft if necessary.

Push/Lock Drain Stopper Removal

Hold the stopper shaft tightly with a finger and unscrew the top.

Levered stoppers

Many tubs, certainly most older ones, have a stopper located inside the drain and overflow tube. Most of these have a lever on the overflow plate and a screen over the drain. The screen keeps most hair out of the drain, but some gets through and eventually forms a clog at the crossbars. Simply unscrew the screen for easy access to this clog and remove it as before. If the drain has an internal stopper, simply unscrew the overflow plate and pull the linkage and stopper up and out. Then clean the linkage and stopper and run water down the drain to flush it out.

Occasionally the linkage is out of adjustment and the stopper doesn't open far enough from its seat to allow a good flow. Adjust it, reinsert it and test it. Run water into the tub. If it leaks out, lengthen the stopper linkage to seal the drain better. If the drain doesn't open to let the water out, shorten the stopper linkage.

Remove the stopper through the overflow.

Remove the stopper through the overflow.

Levered Stopper Removal

First remove the screen and clean the crossbars. Then unscrew the overflow plate, pull out the linkage, clean the stopper and linkage, and rinse the drainpipes. Readjust the linkage if necessary. Reinstall the assembly.

Back to Top

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

    • 4-in-1 screwdriver
    • Needle-nose pliers
    • Utility knife

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.

    • Heavy wire or coat hanger to bend into hook.

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 3 of 3 comments
Show per page: 20   All

August 06, 1:28 AM [GMT -5]

Awesome and no need to buy anything! Repurpose an old metal hanger from the dry cleaner. Warning, though: be prepared to be thoroughly disgusted.


November 23, 7:56 PM [GMT -5]

Our tub drain clogged every few weeks. While looking for a stronger chemical cure I saw a Zip-It. This inexpensive plastic tool cleaned the drain and no trouble for six months.

September 18, 1:32 AM [GMT -5]

I found that a common drill with bit will work very well on clogged bathtub drains. Just stick the drill bit down the drain and pull the trigger. It will wrap all that gunky hair and slime around the bit and then just pull it out.

+ Add Your Comment

Add Your Comment

Unclog a Bathtub Drain Without Chemicals

Please add your comment

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today

Report Abuse

Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us