Video: Self Stick Paint Shield
Tip 1: Roll paint along the edges for consistent texture
1 of 1
Photo 1: Cutting edges
After cutting in close with a brush, the small roller erases all brush marks.
Corners and areas next to trim that are painted only with a brush have a noticeably different texture than the surrounding paint. To ensure the finished texture will be consistent in these areas, brush on the paint, then immediately roll it out before the paint dries.
Use a 3-in. roller with a nap that's the same thickness that was used for the rest of the wall. Roll as close as you can without bumping the opposite wall or slopping paint onto the trim. Finish brushing on the paint and rolling it out in one area before moving on to the next section.
Tip 2: Prime and texture wall patches to avoid a blotchy appearance
1 of 2
Photo 1: Blotchy wall
The dull sheen clearly shows a wall patch.
2 of 2
Photo 2: Prime the patch
Remember to prime the patched area before painting.
Freshly painted walls often look blotchy. The color is uniform, but the sheen isn't consistent. This usually occurs over the holes and cracks you patched with a filler or drywall compound. The porous fillers absorb the paint, dulling the surface (a problem called “flashing”). When light hits these dull spots, they stick out like a sore thumb. The smooth patch also stands out in contrast to the slightly bumpy texture of the rest of the wall. A quick coat of primer is all it takes to eliminate flashing and texture differences.
Primer seals the patch so paint won't sink in and look dull. To match texture, prime with a roller, feathering out the edges. Choose a nap thickness to match the surrounding wall texture (a 3/8-in. nap roller for smooth walls; 1/2-in. for textured).
“I've been in million dollar houses and seen 'flashing' on the walls. It drives me crazy, especially since it's so easy to avoid it.” Butch Zang, president (retired) of Premier Papering and Painting
Tip 3: Cut the tape before pulling it
1 of 1
Photo 1: Cut, then pull
Once cut, the tape comes off cleanly without tearing the dry paint.
Let the paint dry, then cut the tape loose for a perfect edge. Once paint is dry, you can't just pull the tape off the trim. Paint forms a film between the wall and the tape, and removing the tape tears pieces of dried paint off the wall. So before pulling off the tape, cut it loose.
Wait for the paint to completely dry, at least 24 hours, then use a sharp utility knife or box cutter knife to slice through the film. Start in an inconspicuous area to make sure the paint is hard enough to slice cleanly. If you cut the paint while it's still gummy, you'll make a mess. As you cut the paint, pull up the tape at a 45-degree angle.
Tip 4: To avoid lap marks, roll the full height of the wall
1 of 3
Photo 1: Roll the full height
Run the roller up the full height of the wall to keep a wet edge.
2 of 3
Photo 2: Keep going!
Don't let the roller get too dry. Keep it at least half loaded with paint.
3 of 3
Photo 3: You're there!
Finish the stroke, go quickly over any build-ups or runs and start the next stroke.
To avoid lap marks, roll the full height of the wall and keep a wet edge. Lap marks are those ugly stripes caused by uneven layers of paint buildup. They occur when you roll over paint that's already partly dry. (In warm, dry conditions, latex paint can begin to stiffen in less than a minute!) The key to avoiding lap marks is to maintain a “wet edge,” so each stroke of your roller overlaps the previous stroke before the paint can begin to dry.
To maintain a wet edge, paint an entire wall all at once. Start at one end, running the roller up and down the full height of the wall, moving over slightly with each stroke. Move backward where necessary to even out thick spots or runs. Don't let the roller become nearly dry; reload it often so that it's always at least half loaded. Keep the open side of the roller frame facing the area that's already painted. That puts less pressure on the open side of the roller, so you're less likely to leave paint ridges.
“If you paint in sections, you double the amount of work and double the chances of lap marks. I always roll on the paint the full height of the wall, and I haven't had lap marks for 25 years.” Brad Karja, president of Brad Karja Decorating
Tip 5: Feather out the paint where you can't keep a wet edge.
1 of 1
Photo 1: Avoid abrupt edges
Taper the edges by rolling them with a dryer roller.
You can't cover large areas like ceilings, extra-tall walls or stairwells in single, continuous strokes, so the best way to minimize lap marks on these areas is to feather out the paint along the edges that you can't keep wet. The thinner, feathered coat of paint will avoid the buildup that causes the lap mark.
To paint a large section without leaving lap marks, roll the nearly dry roller in different directions along the dry edge, feathering out the paint as you go. After completing the entire length of the wall or ceiling, move to the next section and paint over the feathered edges. For the second coat, apply the paint in the opposite direction. This crisscrossing paint application sharply reduces (if not eliminates) lap marks.
Tip 6: Use cotton drop clothes rather than plastic
1 of 1
Photo 1: Paint on canvas
Canvas gives sure footing; plastic is slippery.
Spills and spatters happen, regardless of how careful you are. It's a lot easier to prepare for them than to wipe them out of your carpeting or off your wood floor later. All it takes is canvas drop cloths in your work area. The thick canvas stays in place, so you don't need to tape it, and you can use it to cover any surface. Plastic drop cloths are slippery to walk on or set a ladder on and don't stay in place. Even worse, paint spills on plastic stay wet, and they can end up on your shoes and get tracked through the house. Canvas is slippery on hard floors, so rosin paper (in rolls at home centers; see Tip 10, Photo 1 below) is better over vinyl, tile and hardwood. Tape the sheets together and to the floor to provide
a nonslip surface.
But even with canvas or rosin-paper drop cloths, large spills still need to get wiped up right away or they'll seep through. Clean spills with paper towels or cloth rags. Likewise, if you splatter paint on any other surface, wipe it up immediately.
Tip 7: Sand trim between coats for an extra smooth finish
1 of 1
Photo 1: Sand trim with a sanding sponge
A sanding sponge conforms to curves and smoothes fine details more easily than sandpaper.
One coat of paint usually won't hide the underlying color and sheen on trim. And if you don't sand the surface smooth between coats, the finish may have a grainy texture. For a smooth finish, sand the trim before applying each coat of paint.
Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can't go and apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
“Painters are really just glorified sanders. Prep and sand the wood, and the final coat is so smooth it looks like it's been sprayed on.” Brad Karja, president of Brad Karja Decorating
Tip 8: Mix cans of paint for consistent color
1 of 1
Photo 1: Mix cans of paint
Mix paint from several cans to assure even color on your walls.
Mix several cans of paint in a large bucket for a consistent color throughout the room. Paint color may vary slightly from one can to the next. If you have to open a new can in the middle of a wall, the difference may be noticeable. Mixing the paints together eliminates the problem. It's best to estimate the amount of paint you'll need and mix it in a 5-gallon bucket (a process called “boxing”). When coverage is difficult to estimate, add more rather than less. You can always pour the leftover back into cans.
For large jobs, use the bucket and a roller screen rather than a roller tray. It's much faster to load your roller with the screen than to use a roller pan. Simply dunk it into the paint bucket, then roll it along the screen until it stops dripping.
Tip 9: Clean dirty surfaces so the paint can form a strong bond
1 of 2
Photo 1: Clean to prevent peeling
Paint doesn't adhere well to skin oils. Clean areas that hands often touch.
2 of 2
Photo 2: Common wall and woodwork cleaners
You'll find such cleaners in hardware stores or home centers.
Paint dirty, oily surfaces and the paint will easily chip or peel off. So before painting, clean grimy areas with a deglosser or heavy-duty cleaner intended for prepaint cleaning. They work well to clean painted, varnished or enameled surfaces to improve the adhesion of the new paint. They're ideal for cleaning greasy or oily areas like kitchen and bathroom walls and removing hand marks around light switches and doorknobs.
Wipe on the cleaner in a circular motion using a lint-free cloth or abrasive pad. Start at the bottom and work up. After the surface is clean, fill in any nicks and holes, then sand them smooth before painting. The cleaners are available at paint stores and home centers. Be sure to wear rubber gloves and eye protection.
“Painting over grease, grime or hair spray is like painting over rust on your car—you've got to get rid of it or the paint won't hold.” Butch Zang, president (retired) of Premier Papering and Painting
Tip 10: Paint the trim first, then the ceilings and walls
1 of 1
Photo 1: Paint the trim first
Brush out the trim before rolling the walls.
Pros usually follow a certain order when painting a room. They paint the trim first, then the ceiling, then the walls. That's because it's easier (and faster) to tape off the trim than to tape off the walls. And you certainly don't want to tape them both off! When painting the trim, you don't have to be neat. Just concentrate on getting a smooth finish on the wood. Don't worry if the trim paint gets slopped onto the walls. You'll cover it later when painting the walls. Once the trim is completely painted and dry (at least 24 hours), tape it off (using an “easy release” painter's tape), then paint the ceiling, then the walls.