Whether it’s a stream in the middle of the woods or a fountain in the heart of downtown, few things rival the sight and sound of moving water. It’s relaxing, mesmerizing, contemplative. Well, you don’t have to pack up the family and drive for hours for that experience. You can create your own water garden, complete with babbling brook, in your own back yard.
We’ll show you how to create a water garden—without spending a fortune or your entire summer doing it. Preformed shells, rubber liners and off-the-shelf pumps and filters put the project’s costs and skill requirements within easy reach of any do-it-yourselfer. You’ll put in your share of sweat equity busting sod and hauling stone. But when you’re done, you’ll have a landscape feature to enjoy for years.
Before making any purchases, get copies of the literature showing the size and shape of the shells your supplier has available. Select a few models, then use a garden hose to create a rough footprint of where they’d go and how they’d connect. We settled on the 210-gallon “Butterfly” pond (about $300) from Atlantic Water Gardens for the lower pond and the 165-gallon “St. Lawrence” pond with spillway (about $190) from MacCourt.
Once you’ve obtained your shells, position them (Photo 1), then use a shovel to trench an outline 6 in. larger than the ponds. Remove the shells and dig (Photo 2) the hole for the lower pond. You need to create a hole that will support the bottom of the shell as well as the ledges. Lower the shell into the hole frequently to check the depth, shape and position of shell and ledges. Dig the hole about 2 in. deeper than the intended final elevation because the sand base you’ll spread next will raise it back up (Fig. A). Make certain the lip of the shell will be at least 2 in. above the surrounding soil or else dirt and muddy rainwater may flow in.
Next spread and level a 2-in. layer of coarse sand over the bottom of the hole (Photo 3). Set the shell in place and check everything out. Does the sand fully support the bottom? Is the shell level (Photo 4) in every direction? Is the lip at least 2 in. above the surrounding soil? Are the edges of any ledges supported? If the answer to all these questions is “yes,” you can start backfilling the pond.
Fill the pond with 2 to 3 in. of water, then check the shell for level again. This is critical; the water in your pond will be level, so if the shell is tilted, the water line will show it! Pack a mixture of half sand and half soil around the base of the pond as you fill it with more water (Photo 5). Be sure to pack sand under the ledges before the water reaches them; they’re flimsy and need support.
Once we had the lower pond backfilled within about 8 in. of the top, we tucked the corrugated hose under the lip of the shell (Photo 6). This hose is used to recirculate water from the pump in the lower pond to the “mouth” at the far end of the upper pond.
Dig the hole for the upper shell, then level it and line it with sand as you did the lower shell. Make sure you have an adequate height difference (Photo 7) for your falls and stream. If you’re building on a slope, you may be able to bury the entire upper shell. Our site was flatter, so we used stone, sand and soil to partially build up around the shell.
Use the level of the water in the shell as a guide for fine-tuning the height of the ledges; the ledges are flexible enough to lift or lower an inch or so to maintain a level perimeter.
You can disguise the lip of your liner with overhanging plants, stone or a combination of both. We primarily used stacked flagstone.
Spread a 1- to 2-in. layer of sand around the lower pond, then set a layer of flagstone so the upper surface is level with the lip of the shell (Photo 8). This allows you to cantilever the second layer of “capstones” over the lip of the pond without them weighing directly on the lip.
There’s no exact science to the stonework part of this project. Use the ugliest, most irregular stones for the first support layer, since you won’t see them anyway. Select and install capstones that conform to the shape of the pond edge. We built and rebuilt the stone layers around the bottom pond several times before we found a pattern we liked.
Once you have the lower pond surrounded with stone, build your way up and around the upper pond. Start with a wide stone base around the upper pond. This will allow you to lay a slightly sloped, stable wall as you build up to the lip. Solidly support the ledges of the pond with rock and soil when you reach them. We created a small rock planter (Photo 9) that stepped up to the upper pond and helped make a more natural-looking transition.
While you’re doing the stonework around the upper pond, snake the free end of the corrugated hose (Photo 6) to the far end of the upper pond. Bury it and cover it within the rocks, but don’t pinch it. Extend the free end of the hose so it discharges into the far end of the upper pond, then secure and disguise the hose with cap rocks.
Connect the filter, pump and hose. Place the lower pond pump and the upper pond inlet hose as far from each other as possible. This will help ensure a more thorough water filtration and minimize stagnation. Keep a careful eye on the water level for several days to make sure there are no leaks or clogs.
We created a small stream from the spillway of the upper pond to the lower pond. We began by building a small canal out of stone (Photo 10), then sloped a layer of sand across the bottom. We then laid the rubber liner into the canal (Photo 11), draped the excess liner up and over the walls of the canal, then added another layer of stone to disguise it. Make sure the canal is deep enough to prevent water from escaping.
Support the liner and curve it up and behind the spillway to contain the water. Make certain the other end drapes well into the lower pond. Use water from a garden hose to test the slope and flow of your little river as you build it. Again, don’t expect to get everything right the first time. Building with irregular stone isn’t the same as building with flat, square wood. Use small stone chips to shim and stabilize larger stones as you work.
Once you’re satisfied with the design and water tightness of your stream, use pond foam (a black, weather-resistant expanding foam available through your pond dealer) to secure thin stone to the top and face of the spillway to disguise it (Photo 12). We added smooth stones to the bottom of the stream to hide the liner and create a more natural-looking flow.
Continue adding stone up and around the upper pond and upper pond lip.
All the Right Stuff
If you want a long-lasting water garden, keep these buying tips in mind:
- Some pond shells are flimsy and more likely to flex under the pressure of heavy backfill or freezing, expanding soil. Do some comparison shopping before you buy.
- Buy the thickest EPDM rubber liner you can find. It commonly comes in 40-mil and heavier-duty 60-mil thicknesses.
- Invest in heavy-duty hose for circulating the water. Once it’s buried, it’s hard to make repairs. The corrugated version we found was quite crush resistant.
- Pump size is based on the desired flow rate, plus the height and distance it needs to push the water. Read the manufacturer’s guidelines; when in doubt, opt for the larger pump.
- Order excess flagstone. You’ll be better off finding shapes that fit than doing a lot of cutting. You can use any leftover material to build a path or a garden border.
If your ponds are full of sand, rock bits and other construction debris, siphon, pump or use a big wet-dry vacuum to remove the water and refill the ponds with fresh water.
Connect the filter and pump to your water circulating line so the water is drawn through the filter before it reaches the pump (Photo 13). We added a T-fitting to our pump so we could circulate water to the upper pond and to a small statue beside the lower pond.
Set the filter on a few small rocks so it doesn’t rest directly on the bottom where it’s more likely to become clogged with debris. Plug in your pump, then keep an eye on water levels and flow to make sure everything is functioning properly and there are no leaks. Pay attention to the pump and filter literature for maintenance information. Keep the upper end of the hose out of the upper pond to prevent a possible siphoning effect.
Maintaining clean water and establishing aquatic plants and fish are complex topics we won’t even pretend to address here. Suffice it to say, understanding the dynamics of your pond and doing proper maintenance will make the difference between a pond you’ll want to linger around for hours and one you’ll want to fill in with dirt and plant with petunias in a few years.