• Share:
Storing and Organizing Car Care Products

Organize your auto lubricants, fluids and other items in this simple shelf/work table cabinet. Build it in a few hours and keep all your auto needs close at hand.

By the DIY experts of The Family Handyman Magazine

Storing and Organizing Car Care Products

Organize your auto lubricants, fluids and other items in this simple shelf/work table cabinet. Build it in a few hours and keep all your auto needs close at hand.

By the DIY experts of The Family Handyman Magazine

Overview: Time, tools and materials

It's a whole lot easier to be a gearhead when all your gear is in one place. Here's an easy-to-build organizer you can complete in one morning, even if you're a beginning woodworker. If you build it from construction- grade pine boards and plywood, the materials will cost you about $40. If you use maple boards and birch plywood as we did, it will cost about $70. The only must-have power tools for this project are a drill and a circular saw, though a table saw and a miter saw would make the job much faster and easier.

Fold-up door

A Fold-Up Door

The worktable is also a door that encloses the bottom shelf. Flip it up and you've got a mounting surface for a towel holder and other accessories. You can mount a fold-up door on special hinges, but we'll show you a faster method that requires just a couple of bucks' worth of hardware (Photos 3 and 4 below).

Step 1: Assemble the shelves

To get started, cut the sides to length, lay them back to back and mark the shelf locations (Photo 1). Then mark and drill 3/16-in. pilot holes for the screws that fasten the shelves. Measure 1 in. and 2-3/4 in. from the back edges of the sides when you locate these holes. Set the 1x4 shelves between the sides and drill pilot holes into the shelf ends using the holes in the sides as guides. Drilling these pilot holes and screwing the shelves into place is easier if you clamp the whole cabinet together first (Photo 2). But you can hand-hold the shelves against the sides if you don't have long clamps. After the shelves are screwed into place, rip 1/4-in. plywood into 1-1/2-in.-wide strips for the front lips on the shelves. Glue the lips to the shelves, using 3/4-in. brads or clamps to hold the lips in place while the glue sets.

To complete the cabinet box, lay it face down and make sure it's square by taking diagonal measurements. Then run light beads of wood glue on the sides and shelves and tack on the plywood back with 3/4-in. brads spaced about 8 in. apart. The back is slightly narrower than the cabinet, so you don't have to line up the edges perfectly.

Figure A: Car care cabinet

Figure A: Car Care Cabinet

Figure A and a complete Materials List are available in pdf format in Additional Information below.

Step 2: Mount the fold-up door and apply finish

Flip the cabinet onto its back and clamp the door into place with the back edge of the door resting flat on your workbench. Using a square, mark the location of the door on the outer sides of the cabinet. Then drill 5/16-in. holes 1-3/8 in. from the front edges of the cabinet sides. Drill through the sides and into the door, stopping at a depth of about 1-1/2 in. (Photo 3). Cut shallow recesses in the door for the T-nuts using a coarse file or wood rasp. Position the door and drive in the machine screws that act as pivot points for the door. Make sure the door opens and closes freely. If not, sand down the edges that bind with a belt sander or an orbital sander. If the fit is a bit sloppy, remove one of the screws and place a washer over the T-nut.

To put a quick finish on the cabinet, remove the door. Sand away any pencil marks and smooth sharp edges. Take the cabinet to a well-ventilated area and apply a couple of light coats of aerosol spray lacquer. The lacquer will harden in just a few minutes. Then lightly sand with a fine sanding sponge and spray on a final coat. Wait about an hour to reattach the door. To mount the cabinet, drive four 1-1/2-in. screws through the back and into studs. Add a dry-erase board and paper towel holder if you like and load those shelves!

Additional Information

Back to Top

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

    • Hammer
    • Tape measure
    • Circular saw
    • Drill/driver, cordless
    • Drill bit set
    • Wood file
    • T-square
    • One-handed bar clamps
    • Wood glue

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.

See Car Care Cabinet Materials List in Additional Information at the end of the Step-by-Step section.

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 1 of 1 comments
Show per page: 20   All

August 03, 8:35 PM [GMT -5]

I have the clutter of fluids problem. However I'm extremely leery of comitting to a flammable indoor enclosure. Got any ideas for constructing a spill protected fire rated outdoor enclosure to maybe go in a shed? Of course the extremes of winter and summer may make this a bad idea....?

+ Add Your Comment

Add Your Comment

Storing and Organizing Car Care Products

Please add your comment

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today

Report Abuse

Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us