How to Fix Squeaky Floors

Five easy ways to silence your floor

First, find the source of the squeak

Floor squeaks are caused by wood rubbing against a nail, other wood, or even ductwork and piping. Finding the squeak can be difficult, but if the squeaking floor is open from below, you’re in luck. You’ll have several options to stop it.

To locate the source of the squeak, have a helper spring up and down on the squeaky area while you listen and watch for subfloor movement from below. Also look for loose nails or subfloor seams rubbing against each other. It doesn’t take much movement to cause a squeak, especially since your floor amplifies the sound like a giant soundboard.

If you’re working alone, measure the squeak’s location in relation to a wall or heating register that you can locate from below. Then go downstairs and measure these distances along the subfloor. Or, if your floor is carpeted, you can drive an 8d finish nail through it to mark the squeak source.

Back to Top

Fill gaps with shims

Finding the exact cause of the squeak, and then choosing the best remedy, isn’t always a simple task. Don’t be surprised if you have to try several solutions before you stop it for good. Look for gaps between a joist and the subfloor first. Plug in a drop light and examine the area closely; a gap or movement may not be obvious.

If you spot a gap, use the wood shim solution to stop floor movement. Shims are available at any home center or lumberyard. Push a pair of shims in lightly. If you drive them in, you’ll widen the gap and potentially create a new squeak. Adding construction adhesive before final assembly makes the fix permanent while filling in irregularities between the wood surfaces.

Back to Top

Reinforce the joists

If you spot wide gaps along sagging or damaged joists or see that a subfloor edge is poorly supported, add blocking to support the subfloor and stop movement. Also keep an eye out for protruding nails and clip them with diagonal cutters. (You may need a strong grip and a few tries to work your way through the nail!)

Measure and cut a 2x4 block that’s 2 ft. longer than the poorly supported area. Apply construction adhesive to the side and top of the blocking before installation to add strength. It should squish out when you screw the 2x4 in place. Predrill screw holes (for 2-1/2-in. wood screws) to prevent splitting the block and to make driving easier.

CAUTION

Construction adhesive contains a strong solvent. Wear a respirator with an organic vapor cartridge when working in closely confined areas.

Back to Top

Fill gaps with construction adhesive

Sometimes the gapping between the subfloor and joist is too narrow, too irregular or too widespread for shims to be effective. Or perhaps you can’t pinpoint the exact source of the squeak. A good solution is to use a bead of construction adhesive to glue the wood together. You don’t have to press the gaps closed; construction adhesive fills the space and hardens. The key is to force it as far as possible into the gaps without widening them. Work both sides of the joist for a strong, lasting connection. And glue nearby joists as well in case you can’t find the exact squeak source. Keep off the floor for a day until the glue hardens.

Back to Top

Block beneath squeaky joints

Once in a while, movement in a subfloor joint will cause a squeak. You can stop it by screwing and gluing 2x8 blocking under the joint to give it solid support. First angle-screw through the blocking, up into the joists, to ensure a tight fit. But be sure to drive additional nails or screws to anchor the block. Otherwise it might work loose and cause more squeaks!

Back to Top

Screw hardwood flooring from below

A solid wood floor is usually fastened with hundreds of nails, so squeaks often occur as the floor ages. But some squeaks aren’t caused by nails; they come from one edge of a board rubbing on another. A simple “first” solution is to dust the squeaky area of your floor with talcum powder, working it into the cracks. The talc reduces friction and may solve the problem, at least for one season.

Note: Talc can be slippery. Wipe off the excess.

For a more permanent solution, however, you’ll usually have to screw the subfloor to the wood flooring from below. Drill a 1/8-in. pilot hole about 1/2 in. less than the thickness of the entire floor, and buy screws 1/4 in. shorter than the floor thickness so they won’t penetrate the surface. You can find your floor thickness by either removing a floor register and measuring the floor where the duct comes through, or by drilling a small hole in an out-of-the-way corner and measuring with a nail.

To maintain a safe margin, mark the desired drilling depth on the drill bit with masking tape. Space your screws about every 6 in. in the area of the squeak. Have someone stand on the floor above while you drive the screws. Set the heads flush with the subfloor. Sinking the head into the subfloor could cause the screw point to break through the finished floor surface.

Back to Top