Cable and Telephone Wiring

Updated: Aug. 28, 2019

Upgrade communications wiring and hardware for better reception with less interference.

FH01SEP_CABLEW_01-2Family Handyman
You can install communication lines that will integrate, connect and route your cable and phone. The system shown here, which can be installed by a DIYer, can be used to update your TV, Internet, phone and future date lines. It's a great way to take advantage of high speed Internet connections and high definition TV.

You might also like: TBD

Time
A full day
Complexity
Intermediate
Cost
$101–250

Cable and telephone wiring basics

Jacks and connectors

These are the connectors and cables used for phones, computers and TVs.

Computer hook up

CAT-5 wires are used to connect your computer to the module.

Telephone hook up

CAT-5e modular jacks are used to make phone connections.

Television hook up

Coaxial cable gives your TV a clearer signal than traditional TV cable.

If you want to set up communication lines and be ready for anything that comes along this century, you need a system that will allow you to integrate, connect, route and modernize telephone, TV, Internet and all future data lines. We can’t guarantee that our system will take care of everything (no one knows what’s coming), but if you install the stuff we show here, you should be set for the next 25 years or so.

You can install the system yourself using tools and materials found at a well-supplied home center. The key to this system is to feed two telephone and two coaxial cables from each wall jack to the central communication center so you can easily link any electronic components in the future. That means buying a lot of cable, but don’t worry—cable is relatively cheap. Phone connections are made by linking different phone ports with “patch cords.” Video cable links are made by connecting cables with cable splitters.

There’s room in the telecommunication distribution box for other electronic enhancements too. At some point, you may want to add computer networking components, hardware to boost video signals and more cable splitters for connecting different components.

Here’s the basic hardware you’ll need:

    1. Telecom distribution box: This box contains the telecommunication module and the connecting hardware that are the wiring hub of the home.
    2. Telecommunication module: This module snaps into the panel and contains the phone terminals and the main cable splitter block. The phone and coaxial cable lines from the street connect to these terminals, as do the lines from the individual jacks in your home. You can add patch cords and splitters to network lines inside your house.
    3. CAT-5e telephone cable: This high-quality cable eliminates interference from internal and external electronic traffic for clear, unobstructed signals. It’s capable of carrying high-speed Internet service as well as up to four telephone numbers.
    4. CAT-5e modular jacks: These are the actual wall terminals that your phones and computers plug into. They come with a special “punch-down” tool for hooking the eight CAT-5 wires into the jack.
    5. RG-6 coaxial cable: This cable is similar to conventional TV cable but made to higher standards for clearer signal transmission. TV went completely digital in 2010.
    6. Crimp-on F-connectors: These are the female plugs that crimp onto both ends of the RG-6 cable to connect into the panel box at one end and into the wall plates at the other. Use a special “Coax Strip and Crimp Tool” to connect the cable to the F-connectors.

Cable-Running Tips:

Avoid tight bends of less than 2-in. radius; smooth, gradual ones are best to protect the wire.

Clamp cables to framing with nylon cable straps, lightly secured around the cables and screwed to the framing. Never compress, crush or deform the wire.

Pull gently on cables when feeding them through holes and tight spaces. Pulling with more than 20 lbs. of force (as if you were really pulling your bootstraps tight) will distort the delicate twists and compromise the quality of signals.

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

  • Corded drill
  • Drill bit set
  • Extension cord
  • Stepladder
  • Tape measure
  • Wire stripper/cutter

You’ll need a special Coax Strip and Crimp tool to connect to the F-connectors. You may also need a fish tape to run wires in finished walls and ceilings.

If you’re running the wires in finished walls, you’ll also need tools to patch and paint the walls.