Having a shop winterize your bike can cost over $200. But if you can change the oil in your car, you can easily winterize your own bike and save most of the cost. Just pick up the items we show here and gather up your tools. The winterizing process takes less than two hours and starts at the nearest gas station.
By the DIY experts of The Family Handyman Magazine:November 2009
Fuel stabilizer works best with fresh fuel, so add it to the tank right at the station. That’ll give the stabilized fuel a chance to run through the carburetor on the way home. Make sure the stabilizer itself is fresh—it’s only good for two years once the bottle’s opened.
Combustion gases collect in your oil and form acid. You don’t want that acid sitting in your crankcase all winter eating away at bearings and other expensive parts. So even if you’ve recently changed it, you need to change it again for winter storage. Yes, it’s that important.
Bikes have low clearance and car drain pans won’t fit. So get a low-profile plastic food storage container (no, not from the kitchen) and use that as a drain pan. Spin on a new filter and refill the crankcase with fresh oil.
Some shops think this step is overkill, but it can’t hurt. Fogging prevents corrosion by covering internal engine parts with a light coat of oil. There’s no downside to it. Just make sure you do this step outdoors—it creates a lot of smoke. If your bike needs new spark plugs, install them before you fog the engine. Start fogging by removing the air filter (the fogging oil will clog the filter material). Then start the bike. Spray the fogging oil directly into the air intake as you increase the idle speed to 2,000 rpm. Stop spraying when the engine quits.
Even though you’ve added stabilizer to the gas, you still have to drain the carburetor. Turn off the main gas valve from the tank. Then look for the petcock or drain screw on the bottom of the bowl. Place a folded rag under the bowl and open the petcock. You won’t see a flood of gas—a carburetor bowl only holds about 2 ozs. Close the valve when the gas stops flowing. Spread the rag out to dry (not in direct sunlight) before tossing it into the trash.
On shaft-driven bikes, remove the drain plug and let the gear lube drain out. Then replace the plug, level the bike and refill with fresh lube. Use a bendable funnel and pour slowly until you see oil seeping out of the opening. Then cap the funnel end with a rag (to catch the rest of the oil in the funnel) and replace the filler plug.
Mufflers and air cleaners are “homes of choice” for critters. Keep them out by stuffing a sandwich bag with steel wool and then pushing the bag into the air intake and tailpipes. The bag keeps steel wool strands out of the engine. Use bright-colored caution tape as a reminder to remove it in the spring.
You should already be doing this several times during the biking season. But it’s especially important to spray chain lube onto the chain and into all pivot points (brake and clutch levers, kickstand, fold-up foot pegs, etc.) before storing your bike for the winter. That’ll keep rust from forming on the parts during the winter.
A battery maintainer won't damage your battery like a trickle charger. They have smart monitoring circuitry that charges the battery only when it needs it. So connect one to your battery and it will be fully charged and ready to fire up in the spring.
This is one step most people skip. Don't. Dip the suction tube of the coolant tester into the radiator or coolant reservoir and suck up enough to make the indicator (or balls) float. Then read the protection level. If yours isn't up to the task, change it now.
This may sound strange, but a light coating of WD-40 over the entire bike does a great job of preventing corrosion. I got this tip from a bike shop service manager who swears that his bikes come out of storage looking better than customers’ bikes that aren’t sprayed. In the spring, just drive it to a self-service car wash and hose it down. It’ll look great.
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
You'll also need an oil filter wrench, oil drain pan, rubber gloves, oil funnel, bendable funnel, a battery maintainer and a coolant tester.
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.
