Finishing a basement is a perfect DIY project. For a fraction of the cost of an addition, you can convert basement space to valuable living space. Advances in waterproofing along with new products mean your basement rooms can be as dry and comfortable as any other room in the house.
Finishing a portion of a basement is an inexpensive way to gain valuable space for a family room, game room or other use. The big question is how to finish the foundation walls. We'll assume that you have either a poured concrete or a cement block masonry wall. With either surface, the finishing options are the same.
Before beginning any work, you must determine whether your basement has any moisture problems. If your foundation walls are only damp on humid summer days, fine—you're good to go with the methods we recommend. But if you have any problems with standing or leaking water in the spring or during heavy rains, you've got some “prework” to do.
Fixes usually are as simple as adding or repairing gutters and downspouts or adjusting the grade to direct runoff water away from the house. But serious water problems may call for drastic measures like interior or exterior drain tiling, or exterior waterproofing, which could mean digging around the house or tearing up part of the slab. You must solve all water problems, or you'll risk boxing future water in behind a finished wall, ruining it. You'll end up spending hundreds of bucks re-remodeling a recently finished lower level.
Just about every carpenter or building inspector has a different opinion on how to finish walls against masonry. The methods we'll demonstrate work well in most conditions, but consult with your building inspector before beginning any work to make sure you're meeting building codes in your area.
Use a paint roller to apply the waterproofing product you choose.
Masonry waterproofing products are available at home center stores.
Once you've solved the moisture problems, seal the foundation walls. Start by rolling on a masonry waterproofing product. This step is only to help prevent water that naturally migrates through concrete through a capillary effect.
Roll-on waterproofing is in no way a permanent solution to a bulk water infiltration problem. If the walls are damp from condensation, dry them out with a humidifier before using the product. One choice is DRYLOK, which is available at home centers and hardware stores.
Phil Geis has been a framing carpenter for more than 20 years. He started out helping his uncle on remodeling projects while he was still in high school. He and his crew have built more than 300 new houses and breathed new life into dozens of old basements.
Screw or nail one side of the block through the joist, and secure the other side to the sill plate. Use treated lumber if the brace will come in direct contact with bare concrete.
When the floor joists run parallel to the wall you're building, you'll need to install blocking for attaching the top wall plate. Screw or nail one side of the block through the joist, and secure the other side to the sill plate. Use treated lumber if the brace will come in direct contact with bare concrete. It may be easier to install the braces before you install the foam board on the walls and insulate your rim joist. (See more on How to Insulate Basement Rim Joists.) Phil places his blocks 2 ft. apart so they work as drywall backers too.
Apply the adhesive vertically to keep water from pooling behind the foam insulation.
After your waterproofing has dried, install 2-in. extruded polystyrene (XPS) foam board insulation. Be sure you use XPS—other types are not as moisture resistant. Stick it to the wall with a construction adhesive that's specifically designed for foam—regular construction adhesives will melt the foam.
Apply the adhesive in vertical strips in the middle of the wall. If some water does get behind the foam, adhesive applied horizontally could cause the water to pool up and lengthen the time it takes to dry up. Run a continuous bead of adhesive at the top and bottom of the wall, and tape all the seams. This will help keep warm air in the room from getting behind the foam and condensing on the cool concrete walls. To ensure a good seal, Phil prefers to caulk the bottom after the foam is installed.
Snap a line on the floor 4 in. away from the foam as a guide for the bottom plate.
Snap a line on the floor 4 in. away from the foam as a guide for the bottom plate. This will leave a 1/2-in. gap between the bottom of the new wall and the foam. That'll allow a bit of wiggle room if the foundation walls aren’t perfectly plumb or straight.
It's faster and easier to assemble a wall on the ground—if you have the space!
If you have the space, it's faster and easier to assemble a wall on the ground. Sight every stud for a “crown” (a slight curve on the narrow side of the board), and mark an “X” on the crown. Have all the crowns face the same direction. If you don't, you’ll end up with a wavy wall.
It's easier to assemble your wall with the crowns up; that way both ends of the studs are solidly on the ground when you attach the top and bottom plates, instead of acting like rockers on a rocking chair. Build the wall so it can be tipped right up; there's usually not enough room to swing the whole wall around if you don't.
If the floor joists are sagging or there's ductwork in the way, you may have to lift the top of the wall in first and slide the bottom plate into place as shown here.
It's usually easier to tip a wall up with the bottom plate against the wall, but if the floor joists are sagging or there's ductwork in the way, you may have to lift the top of the wall in first and slide the bottom plate into place. If you're working alone, don't build a wall too heavy to lift. Save your back by building smaller sections and tying them together after you set them in place.
If you need to pound the walls into place with a sledgehammer, you've built your walls too tall. There's no reason that the top plate has to be tight against the joists—that's what shims are for. Measure the distance from the floor to the joists at several locations and build your wall at least 1/4 in. shorter than the shortest measurement. Trying to force a wall into place can raise the joists, which could wreak havoc with drywall joints and flooring on the rooms above.
First put construction adhesive on the floor, then tip the wall into place and fasten with concrete nails or screws. Space fasteners every 6 ft. and within 6 in. of each end.
Phil fastens his walls to the floor with construction adhesive and a powder-actuated tool (PAT). He spaces fasteners every 6 ft. and within 6 in. of each end. Most residential-grade PATs are powered by .22 caliber blank cartridges, which drive in nail-like fasteners at a velocity of about 300 ft. per second. Prices range from $20 for the one in this photo up to $80 for models that have a trigger and don't require a hammer to fire them. Get 2-1/2-in. fasteners so they will penetrate about 1 in. to 1-1/4 in.
Wear safety glasses, and hearing protection is a must because these suckers are loud. Phil usually shouts out “Fire in the hole” to warn other people in the area. For more information on PATs, check out How to Use Powder Actuated Tools.
Plumb the wall about every 4 ft. You need shims only about every third joist, but nail the top plate to every joist.
Instead of snapping a line for the top plate, Phil plumbs the wall about every 4 ft. using an adjustable level that reaches from the bottom plate up to the top. If you don't own a $300 plate level, use at least a 4-ft. level, and try to find the straightest studs to use as a guide. You need shims only about every third joist, but nail the top plate to every joist. It's not necessary to align the studs directly under floor joists, but it's a good idea if you plan to run ductwork or plumbing in the walls.
If your floor is horribly out of level, or if you're framing around a window, it may be best to “stick frame,” nailing one stud at a time instead of building the wall on the floor.
Start by fastening your bottom plate, and then use a straight stud and a level to plumb up to find the location for your top plate. After you snap a line and fasten your top plate, plumb up again and mark the location of your first stud on both plates. Mark the rest of the stud locations on the plates using those marks. Toenail each stud into place with two nails on one side of the stud and one on the other.
Turn the last stud on the first wall sideways and overlap it about halfway past the connecting wall to create drywall backing.
When he frames inside corners, Phil turns the last board on the first wall sideways and overlaps it about halfway past the connecting wall. This way he can fasten the two walls together and still have a surface for attaching the drywall.
Windows set in a block or concrete wall will need wood around them in order to attach the drywall or jamb extensions.
Windows set in a block or concrete wall will need wood around them in order to attach the drywall or jamb extensions. If there's room, use foam under the boards, and tape the seams to the foam you've installed on the wall. If there's no room for foam, make sure to use treated lumber, but still tape the seams. Construction adhesive and concrete screws work best to attach these boards. Install the wood around the window before you build your wall. That way you'll know exactly where the new wall framing needs to be.
It's a lot easier to add drywall backers while you still have all your framing tools out and before you fill the wall cavities. So before you pack it up, walk around the entire work area and make sure the ceiling and all walls have a sufficient nailing surface for the drywall. The top of outside corners, perpendicular intersections, and walls that run parallel to the joists are three of the most common areas where you'll need to add backers.
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
Depending on the method you choose, you'll need a hammer or a hammer drill to frame the walls and connect them to the concrete foundation.
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.
You'll also need fasteners, wall sealer, foam adhesive, house wrap tape