How to Diagnose and Repair a Broken Auto Light Socket

Updated: Apr. 05, 2023

Use simple detective work to unravel the mystery of a dead light

repair a broken auto light socketFamily Handyman

Headlight out?
Use these four simple steps to determine if your bad headlight or taillight is caused by a burnt-out bulb, a corroded socket or a bad wire.

You might also like: TBD

Time
An hour or less
Complexity
Beginner
Cost
Varies

Broken Headlight Step 1: Replace the bulb

Start with the obvious suspect

Many new car bulbs are easily accessed from under the hood by turning a retaining ring and pulling the bulb socket out, but if you have to access the bulb by removing a lens (see your owner’s manual), you may need to buy a “torx tip screwdriver. Remove the old bulb and insert the new bulb. Don’t touch the glass of the bulb with your bare hands because the oils on your skin can cause the bulb to fail. Reinsert the socket into the headlamp housing and turn on your lights. If they work, you’re done; if they don’t, go on to the next step.

When a headlight goes out, the problem is usually a bad bulb, which is easily replaced. However, the problem could also be a corroded socket or a bad wire. Keep in mind that when several lights are out, such as both headlamps or both taillights, the problem is most likely a fuse. If the fuse is bad, you can replace it and most likely be on your way. Find out everything about your vehicle’s lights.

In this article, we’ll show you how to replace the bulb, and if that fails, we’ll show you how to diagnose a bad socket and probe the wiring with a simple 12-volt automotive test light.

Broken Headlight Step 2: Clean the socket

Be suspicious of corrosion

Turn off the light switch and remove the bulb again. Clean the socket with electrical contact cleaner, which is available at auto parts stores. If you see heavy corrosion, scrape it off with a small screwdriver or wire brush. Then move on to Step 3.

Broken Headlight Step 3: Test the socket

Check all contacts

Test for power at the socket. Turn on the light switch, then ground the tester to a clean screw on the body of the car. Probe the contacts to see if the tester lights. If the contacts look corroded, scratch the surface, but be careful not to bend or distort them. The tester should light for two out of three contacts (one won’t because it’s a ground). If two of them light, insert the bulb. If the bulb still doesn’t work, replace the socket. If only one or no contact shows power, go to Step 4.

Be careful not to touch two contacts at the same time or you could cause a short circuit and blow a fuse.

Replacement bulb and test light

If a new bulb doesn’t do the trick, use a tester to help find the problem and repair a broken auto light socket.

Broken Headlight Step 4: Test for power at the wires

The socket may have gone bad

Push the point of the tester through the wire insulation behind the socket to make contact with the wire. The tester should light for two of the three wires (the ground wire won’t light). If it lights for two wires, the wiring is good. Simply replace the socket. If not, you may have a bad wire or connector somewhere, so check for any visible problems. You may have a problem you can’t find. In that case, make an appointment with your mechanic to check it out.

Tip: Make sure your test light works before doing any diagnostics. Connect it to the negative battery terminal (or any good body ground) and touch the probe end to the positive-side battery terminal. The test light should light up.

Required Tools for this repair a broken auto light socket project

The only tools you’ll need are a 12-volt auto test light, a small screwdriver or wire brush for scraping corrosion, and (possibly) a “torx” tip screwdriver.

Required Materials for this repair a broken auto light socket project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • Electrical contact cleaner
  • Headlamp bulb