• Share:
How to Apply Paint Protection Film

Formerly a pros-only product, paint protection film is now available in easy-to-apply spray-on kits. An expert from 3M shows how to do it.

By the DIY experts of The Family Handyman Magazine

Spray-on paint protection

The paint on the leading edge of car hoods is on the front line for gravel and sand damage. Until recently, you only had two ways to protect the hood: install a “bra” or apply paint protection film. Bras are not only ugly but also lower gas mileage and trap road grit, which damages the paint. Paint protection film looks and works much better, but professional installation costs about $500. Now there's a product that DIYers can apply to protect against paint chips—spray-on/peel-off paint protection film.

Several companies make this paint film, but we chose the 3M Paint Defender product for this story because it lasts up to a year. It costs about $25 and contains enough material to coat the bottom third of your hood. Find it at any auto parts store. We asked 3M product expert Todd Mathes to walk us through the prep and application process.

You'll also need car-washing supplies, poly sheeting to cover the entire car and ground, clean-edge masking tape and a microfiber cloth. Or buy the optional installation kit and a spray trigger. The entire job takes less than two hours. Here's how it's done.

Prep the vehicle

The engine and hood must be cool when you apply the product. A hot engine will heat the hood and force-dry the spray between coats, defeating its self-leveling feature. So check the weather report and pick a time when it'll be cool, dry and calm. Park the car in a shaded area the night before. Then start the project by washing the car with car wash soap. Make sure you remove all traces of bug splatter and tar. Then rinse and dry completely.

Next, pop the hood and prop it open about 4 in. with a roll of paper towels or a block of wood.

Tarp, tape and wax

Spread a poly sheet over the entire vehicle. Then spread sheeting on the ground to catch any overspray. Starting at the grille, use a scissors to cut straight up the center of the poly, stopping about 18 in. from the bottom edge of the hood. Then cut right and left out to the fenders until you have formed a “T” cutout. Tuck the flaps under the hood and tape them inside the engine compartment to prevent them from moving while you spray. Secure the rest of the sheeting to the car and floor with tape to prevent it from blowing onto the wet finish.

Next, tape the top of the “T” to the hood. Apply another layer of tape to form the clean edge between the spray film and the rest of the hood (Photo 1). Once the poly is in place, apply the synthetic wax included with the product (Photo 2). Waxing is an important step to make removal easier a year from now. So even if you've recently waxed the car, do it again using the wax packet included with the product.

Apply the coating

Shake the can of 3M Paint Defender for a full minute before applying. Then hold the nozzle 6 to 8 in. from the hood and apply three coats to one-half of the hood (Photo 3). Spray all three coats in one continuous motion (don't stop and start at the ends of each row or coat). Move the can at the rate of six seconds per pass. Continue spraying onto the fender, over and above the tape line, and below the bottom edge of the hood to get a uniform film thickness at the edges. A proper application of the paint protection film should have an “orange peel” texture and a slightly milky look. Don't worry—the product self-levels and dries clear. Then spray the second half of the hood. When you're done, remove the clean-edge tape while the spray is still wet (Photo 4).

Park the car in the sun and let it dry for two to four hours. The film cures fully in one to four days, depending on the air temperature and humidity.

Troubleshooting

  • If bugs or leaves land on the wet spray, pluck them off immediately with a pair of tweezers.
  • If the spray is solid white, has lumps or develops sags, you've applied too much. Stop spraying and let the product dry. Then peel it off and start over, moving a bit faster and applying less product.
  • If the wet spray has a “dry” look or you've missed areas or pinholes, you can apply more product. But do it quickly. You only have a 10-minute window. Wait too long and the product loses its self-leveling quality and you can wind up with a textured look.

A year from now

Our expert says that the film can last a bit longer than one year but may yellow from UV exposure. However, the longer you wait, the harder it is to remove, so don't push your luck. Pop the hood and peel the film loose around all three edges using your fingernail. Then remove all the film (Photo 5).

Back to Top
closeX

Add Your Comment

How to Apply Paint Protection Film

Please add your comment
closeX

Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

  • Forgot your password?
Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

  • Get a FREE Traditional Bookcase Project Plan
  • Sign up for FREE DIY newsletters
  • Save projects to your project binder
  • Ask and answer questions in our DIY Forums
  • Share comments on DIY Projects and more!
Join Us Today
closeX

Report Abuse

Subject
Reasons for reporting post

Free OnSite Newsletter

Get timely DIY projects for your home and yard, plus a dream project for your wish list!

Follow Us