Car Battery Care

How to care for your car battery

Avoid an expensive service or tow charge (and the worry of being stranded!) by keeping your car battery working at peak performance. This article will show you how to perform a simple step-by-step 10-minute seasonal battery check-up so you know whether your battery is performing well. This article will also explain how to replace your battery if it's failing, so you're not left stranded out in the middle of nowhere with a car that won't start.

By the DIY experts of The Family Handyman Magazine

TIME

Instant!

COMPLEXITY

Simple

COST

Free!

Caring for your car battery

The last thing you need is a car that won't start because the battery is dead. You can avoid that expensive service or tow charge (and the worry of being stranded!) by carrying out a 10-minute seasonal battery check along with a few maintenance tips.

In addition to a set of wrenches, you'll only need a post cleaner or side terminal, a hydrometer and a cable puller, all available at auto parts stores. Keep in mind that you can skip the battery service if you make sure the mechanic does it during periodic servicing, but you'll want to keep up with the regular maintenance.

Back to Top

Step 1: Clean the cables

First clean the top of the battery and any corrosion from the cables using a tablespoon of baking soda, a cup of water and a nonmetallic brush. Flush with cool water. Now disconnect the cables, starting with the negative one to prevent your wrenches from arcing on a nearby ground. Loosen the battery cable clamp bolts and gently give them a twist. Use a cable puller if they're stuck. Never pry on the battery posts. If you have a side post terminal (not shown), use a 5/16-in. box wrench to loosen the cables. With the cables removed, further clean off the corrosion around the battery terminals and cables with a post cleaner.

Back to Top

Step 2: Check the level of the electrolyte

Gently pry off the covers of the battery cells. (We discuss what to if you have a no-maintenance sealed battery later in this step.) The water and acid mixture in the battery (electrolyte) should be about 1/2 in. deep or to the bottom of the fill hole. If it needs water, use clean distilled water, being careful not to overfill the cells, and then inspect the battery case for cracks. If you find a crack, replace the battery. If you added water, let the water mix with the electrolyte for a few hours before the next step. (You may need to reconnect the battery to maintain your memory functions.)

Back to Top

Step 3: Check the condition and charge of the battery

Test the electrolyte in each cell. Squeeze the ball and draw the solution into the tester. Carefully hold the tester level and write down the reading. Squirt the solution back into the same cell. The testers are calibrated assuming a battery is at 80 degrees F. Add .04 to each reading for every 10 degrees above 80 and subtract .04 for every 10 degrees below. If you get a cell reading that differs from the others by .05 or more, replace the battery. A fully charged battery should have a reading of 1.265 or higher. If all the readings show fair or low (1.200 is low) but are consistent, recharge the battery. Learn how to replace a car battery in our video tutorial.

Back to Top

Step 4: To drop in the new battery first remove the cables

Remove your battery hold-down clamp. Disconnect the negative cable first, then the positive. Note: Always replace the battery with one that has a higher rating than the original.

CAUTION

Always wear eye protection and rubber gloves when working on batteries, and never smoke around them!

Back to Top

Step 5: Replace the battery

Tie a heavy-duty strap to the ears on the side of the battery and gently lift it out. Be careful; battery acid is dangerous. Don't drop it. Once the battery is out, clean the battery tray and replace it if it's badly corroded. Batteries are heavy and need solid support!

Back to Top

Step 6: Reinstall the clamp and cables

Carefully lift the new battery into place. Connect the hold-down clamp, then connect the cable to the positive terminal first and the negative last (for negative ground systems). Smear a little petroleum jelly onto the terminal before fastening the cable clamps to the posts. The grease will help slow corrosion. Most batteries are at least 75 percent charged when you buy them and should be ready for you to start your car and drive. Check with your supplier to see if your new battery needs charging before you use it.

Battery Storage: Use a Battery Maintainer

You've emptied the gas, sealed the exhaust and prepared the engine for seasonal storage. But before you throw the tarp over your boat or roadster for the long winter sleep, think about how you're going to care for the battery.

Batteries lose their charge when they sit idle, and when that happens, you could wind up with a worthless battery in the spring. To keep batteries healthy, they should be charged every six weeks. But leaving a standard battery charger connected for the whole season isn't a good idea—that will overcharge the battery and shorten its life. Instead, invest in a “battery maintainer.”

Battery maintainers are designed to be left on for the entire off-season. They monitor battery voltage and automatically adjust the charge to avoid under- and overcharging.

Battery charger/maintainers and quick-release terminals are available at most auto parts stores or online.

Battery Maintainer
Telltale Signs of a Low or Failing Battery

  • Your headlights look dim at idle and then brighten when you rev the engine.
  • The starter turns slowly, barely starting the car. But you may have alternator wiring problems that prevent the battery from fully charging. If that's the case, schedule a service appointment. Check your fan belt. If it's loose, frayed, cracked or glazed, have it serviced or replaced.

A low battery can also be caused by:

  • Frequent short trips.
  • Too many accessories left on or added.
  • Look for a purchase date chart on the battery (it may be handwritten). The battery case will also have a decal stating its expected life, such as 60 or 84 months. If it's near the end of this expected service life, replace it.

Back to Top

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

  • Wrench set
  • Paintbrush
  • Safety glasses

You'll also need a post cleaner or side terminal, a hydrometer, a cable puller and rubber gloves

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here's a list.

  • petroleum jelly