Drywall/Sheetrock Sanding Is Time Well Spent

Home > DIY Projects > Wall & Ceiling > Drywall Tips > Drywall > Sheetrock Sanding Is Time Well Spent

Save
X
Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

Email Address

Password

Remember me on this computer

Forgot your password?

Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

Get a FREE Traditional Bookcase Project Plan

Sign up for FREE DIY newsletters

Save projects to your project binder

Ask and answer questions in our DIY Forums

Share comments on DIY Projects and more!
Join Us Today

User Comments
Write a comment about this project
+ Add Your Comment

Sanding drywall isn’t exactly fun. But if you do it right, you’ll be rewarded with a great-looking paint job that will make all the effort worthwhile. These tips will help you avoid common drywall sanding mistakes so you can get the best results possible from all your hard work.

TIME
Not available

close X

TIME
[–] Hide details

COMPLEXITY
Not available

close X

COMPLEXITY
[–] Hide details

COST
Not available

close X

COST
[–] Hide details

Use a special sanding tool
Choose fine sandpaper for the best results
Fill gouges—don't sand them
Spot problem areas with a handheld light
Prime the walls, then sand again
Use a sanding sponge for corners
Sand with a light touch
Dustless walls

Article

Use a special sanding tool

1 of 1

Use a hand sander and precut sandpaper

Use a hand sander ($6), a package of 150-grit drywall sanding paper that’s precut to fit your sander, and a sanding sponge for corners and detail sanding. You’ll also need a double-strap dust mask rated for nuisance dust and goggles to keep the dust out of your eyes. A hat or scarf to keep the dust out of your hair is a good idea too. Sand with light pressure along the edge of seams and around screws to avoid “fuzzing” the drywall paper. Sand the center of seams just enough to remove ridges and bumps.

Choose fine sandpaper for the best results

1 of 1

Heavy-grit paper will leave sanding marks

It’s tempting to buy 80-grit paper to speed up the sanding job. But because modern lightweight joint compound is so soft, you don’t need heavy-grit paper to sand it. Coarse-grit paper or sanding screens will leave undesirable sanding marks. We recommend precut sheets of 120-grit or 150-grit paper for the best results. Make sure the paper is taut by first anchoring one end under the clamp. Then push the other end under the other clamp with one hand while you tighten the clamp screw with the other.

Fill gouges—don't sand them

1 of 1

Use joint compound to fill depressions

Don’t try to sand out gouges and big ridges. It’s much easier just to trowel on another coat of joint compound. This is especially important at the edge of joints, where too much sanding will damage the paper face on the drywall. It’s quick and easy to trowel a thin coat over the edge of the seam to fill a depression. Touch up grooves and large ridges with another coat of joint compound rather than trying to sand them out. It may take a few coats to fill deep grooves.

Spot problem areas with a handheld light

1 of 1

Then mark problems spots with a pencil

Do a once-over with your hand sander, making sure to hit every surface with joint compound on it. Keep a pencil handy to mark problem areas that need filling or detail sanding. Then get a handheld lamp and go back over the job while shining the light parallel to the wall surface. Use your hand sander and sponge sander to touch up trouble spots. Mark depressions and other spots that need filling. Finish the job by filling the marked areas with joint compound and finally sanding these spots when they dry.

Prime the walls, then sand again

1 of 1

Repriming removes fuzz and lumps

Sanding after priming is a critical step that most beginners skip. But sanding at this stage removes paper fuzz and lumps that will show through your paint job. This is also the time to take care of other imperfections by filling them with joint compound. Don’t forget to sand and reprime these touched-up areas or they’ll also show up when you paint the walls. Prime the walls and sand them lightly after the primer dries to remove paper fuzz and lumps.

Use a sanding sponge for corners

1 of 2

Hand sanders gouge corners easily

Sanding inside corners with a hand sander is asking for trouble. In the first place, it’s difficult to get a crisp corner. But even more troublesome is the tendency to scuff or gouge the opposite side of the corner with the edge of the sander. It’s OK to sand within a few inches of the corner with your hand sander. Then go back and touch up with a sanding sponge or folded piece of drywall sanding paper.

2 of 2

A sanding sponge makes a crisp corner

With a hand sander, it’s easy to get too close and gouge the corner. If that happens, touch it up and try again, with a sponge this time.

« Previous Photo Next Photo »

Sand with a light touch

1 of 2

Use moderate to light pressure

Even though using a hand sander is straightforward, the drywall pro we talked to offered these helpful tips. Use moderate to light pressure and avoid sanding over the same spot in a straight line. This can leave a groove or depression that will show up when you paint. Instead, move the sander around on the joint as you sand. If you do sand too much in one spot, touch it up with joint compound and resand when it dries.

2 of 2

Angle the sander slightly

Keep the sander angled slightly. Press lightly and avoid scrubbing back and forth in one spot. Don’t sand over electrical boxes or other openings. The edges of the box can rip your sandpaper, or a piece of the paper facing on the drywall can roll up under the sander and tear off. Keep a few inches away from electrical box openings and touch up around them later with a sanding sponge.

« Previous Photo Next Photo »

Dustless walls

1 of 1

Wet-sand joints to limit dust

To limit the dust, consider wet-sanding the joints. Tape with care so you don’t have to do much sanding. Then buy a big flat drywall sponge ($2 at home centers), wet and wring it out, and simply wipe smooth any minor flaws. You probably won’t have to use the coarse side of the sponge unless you have unusually rough areas.

Comments

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 1 of 1 comments

Show per page: 20 All

Sort by: Newest First Oldest First

+ Add Your Comment

nrpardee

January 09, 9:01 PM [GMT -5]

I much prefer sanding screens rather than sandpaper. It's doesn't clog up and lasts a long time. I'm also finding that I'm using a sanding spongs more and the sander/sanding screen less.

+ Add Your Comment

closeX