Tips for Easier Electrical Wiring

Home > DIY Projects > Electrical > DIY Tips On Wiring > Tips for Easier Electrical Wiring

Save
X
Log in to My Account

Log in to enjoy membership benefits from The Family Handyman.

Email Address

Password

Remember me on this computer

Forgot your password?

Don’t have an account yet?

Sign up today for FREE and become part of The Family Handyman community of DIYers.

Member benefits:

Get a FREE Traditional Bookcase Project Plan

Sign up for FREE DIY newsletters

Save projects to your project binder

Ask and answer questions in our DIY Forums

Share comments on DIY Projects and more!
Join Us Today

User Comments
Write a comment about this project
+ Add Your Comment

Whether you have years of wiring experience under your belt, or you’re a novice, this collection of tips and techniques will help you wire faster and better. From straightening cable to labeling wires, our master electricians share their favorite tricks for making every wiring job the best it can be.

TIME
Not available

close X

TIME
[–] Hide details

COMPLEXITY
Not available

close X

COMPLEXITY
[–] Hide details

COST
Not available

close X

COST
[–] Hide details

Uncoil without kinks
Pack boxes neatly
Peel UF like a banana
No-snag fish tape connections
Identify roughed-in wires
Test before touching
Troubleshooting GFCIs
Multiple switches, one hot wire
Strip sheathing first

Article

Uncoil without kinks

1 of 2

Lift a few loops from the center of the roll

Pulling plastic-sheathed cable through holes in the framing is a lot easier if you straighten it out first. If you simply pull the cable from the center of the coil, it'll kink as you pull it through the studs. The trick is to lift a handful of coils from the center of the roll and toss them across the floor as if you're throwing a coiled rope.

2 of 2

Straighten before pulling through framing

Next, walk along the length of cable, straightening it as you go. The electricians we talked to prefer this method because they can keep the cable contained in the plastic wrapper for easier handling and neater storage.

« Previous Photo Next Photo »

Pack boxes neatly

1 of 1

Fold the wires to save space

Here’s how to keep wires neat and compact: First, gather all the bare ground wires along with a long pigtail and connect them. Fold them into the back of the box, leaving the pigtail extended. Next, do the same for the neutral wires. If you’re connecting switches as we show here, you don’t need a neutral pigtail. Leave the hot wire extra long and fold it back and forth across the bottom of the box. Put a wire connector cap on the hot wire to identify it.

Peel UF like a banana

1 of 2

Twist the end with two pairs of pliers

Underground feeder (UF) cable has a tough plastic sheathing that’s difficult to remove—unless you know this trick. Start by separating the black and white wires from the bare copper by grabbing each with pliers and twisting. They’re easy to tear apart once you get them started. Pull them apart until you have about a foot of separated wires.

2 of 2

Strip off the sheathing

Next, remove the sheathing from the insulated wires by grabbing the end of the wire with one pliers and the sheathing with another pliers and working them apart. After you get the sheathing separated from the insulated wire at the top, just peel it off. Repeat the process to remove the sheathing from the black wire. Finally, cut off the loose sheathing with scissors or a knife.

« Previous Photo Next Photo »

No-snag fish tape connections

1 of 1

Wrap fish tape and cable with electrical tape

To pull wire smoothly with fish tape, start by stripping an 8-in. length of cable. Using a side cutters, cut off all but one wire. Cut at a steep angle to avoid a “shoulder” that could catch on something. Then bend the single wire around the loop on the end of the fish tape and wrap the whole works with electrical tape to form a smooth bundle. Now you can pull the wire without worrying that it might fall off, and the smooth lump won’t get snagged by or stuck on obstructions.

Identify roughed-in wires

1 of 2

Code your wires

Save yourself a lot of headaches by identifying the wires as you install them. It’s a lot harder to figure out which wires go where when they’re covered with drywall. The electricians we talked to use a “code” for marking wires, and so can you. Here’s one example. Wrap three-way switch “travelers” loosely and wrap the common wire tightly around them for easy identification later.

2 of 2

Label wires

Another method is to use scraps of plastic sheathing to label the wires. Here we labeled the wires that will be GFCI protected. However, by the time you get back to connect switches and outlets, you might find that drywallers, tapers and painters have covered the label or knocked it off. That’s why it’s best to use non-label coding whenever possible. Develop a system and write it down. You’ll never have to guess which are the “line” and “load” and which wires are the travelers for your three-way switch.

« Previous Photo Next Photo »

Test before touching

1 of 1

Avoid surprises

Use a noncontact voltage detector to check every wire in the box or area you’re working. Always check the tester on a wire or cord you know is live to make sure it’s working before you rely on it. Noncontact voltage detectors are available at home centers, hardware stores and online and range in price from $5 to $25. The Klein NCVT-1 tool shown here ($16 at amazon.com) has a green light that indicates it’s turned on and working—a nice feature that’s well worth the extra money.

Troubleshooting GFCIs

1 of 1

Troubleshoot with a GFCI tester

Most complaints occur when several outlets are protected by one GFCI. To determine whether the problem is with the GFCI itself, or downstream, turn off the power to the GFCI and disconnect the wires from the “load” terminals. Push the reset button and plug a GFCI tester into the GFCI outlet before you turn the power back on. If the GFCI trips after you turn the power on, replace it. If it holds, then the problem is with one of the downstream outlets.

Multiple switches, one hot wire

1 of 3

Save box space

A box with three switches is crowded enough without adding extra wire connectors and pigtails. Here’s a wiring method that eliminates extra connections and creates a neater installation. Instead of running a separate pigtail from the hot wire to each switch, just leave the hot wire extra long. To connect the switches, simply score the wire with your wire stripper and push the insulation to expose about 3/4 in. of bare wire.

2 of 3

Go from switch to switch

Wrap this bare section at least three-quarters of the way around the screw terminal of the first switch. Repeat the process for the remaining intermediate switches.

3 of 3

Loop wire around screw in the last switch

Connect the last switch in the usual manner, looping the wire around the screw in a clockwise direction.

« Previous Photo Next Photo »

Strip sheathing first

1 of 2

Mark the spot with your thumb

It’s tempting to push your roughed-in cable through the knockouts in the box and worry about how to strip the sheathing later. But that’s the hard way. It’s much easier to remove the sheathing before you push the wires into the box. The only trick is to make sure you have the cable in about the right spot before marking it and removing the sheathing.

2 of 2

Strip the sheathing at the mark

Score the sheathing at the “thumb mark” and slide it off. Then feed the wires into the box. As long as you don’t have the cable stretched tight, there will be enough “play” to make final adjustments after you’ve inserted the conductors into the box. Remember, the electrical code requires that at least 1/4 in. of sheathing be visible inside the box.

« Previous Photo Next Photo »

Comments

Comments from DIY Community Members

Share what's on your mind and see what other DIYers are thinking about.

1 - 6 of 6 comments

Show per page: 20 All

Sort by: Newest First Oldest First

+ Add Your Comment

stacey01

January 11, 1:35 PM [GMT -5]

Thanks for all the advice. My husband thinks he can handle our electrical wiring in Kennewick WA so I thought I would find him some tips to make things easier. Thanks for the advice! Wish us luck!

lyleparker

October 23, 5:06 PM [GMT -5]

as far as labeling goes...make a sharpie your best friend. Mark an "HR" on the inside of the first box you pull to from the panel. HR stands for homerun and is the first device connection point from the panel. This makes it much easier to troubleshoot later should something go wrong. Additionally, use a long piece of plastic sheathing to write what will be on your circuit and slip it over the "hot wire" in your panel during the rough-in. This way, when you cut-in your panel and make all your breaker connections, you won't spend hours with two guys and walkie-talkies trying randomly flip breakers on and off to label your panel correctly. After you get your breakers connected simply lean your cover against the wall, look at the label on that particular wire, and label your panel accordingly. The few minutes that it will take during the rough will save you hours on the final trim work.

poppyo

January 26, 1:20 AM [GMT -5]

Re: stripping covered cable. They make a cheap, aluminum stripper for 12/2 etc. worth carrying in your toolbox. I have 2 electrician brothers-in-law that turned me on to it, & I have one in my "Electrical" toolbox.

poppyo

January 26, 1:20 AM [GMT -5]

Freeb

January 22, 1:00 PM [GMT -5]

Another no-no I spotted was the the outlet is "backstabbed" which is against most electrical codes these days (and it isn't taped, but maybe that comes later).

November 15, 7:26 AM [GMT -5]

UNCOIL WITHOUT KINKS

I agree that taking coils out of the package as you suggest is correct, however, the coil must be "walked", that is, hand over hand to the end of the coil.

Throwing the coil, no matter what size, would allow it to go about five feet and you would still have to untangle the wire.

+ Add Your Comment

closeX